- 30 Jun, 2021 40 commits
-
-
Zheng Yongjun authored
[ Upstream commit 9d44fa3e ] Function 'ping_queue_rcv_skb' not always return success, which will also return fail. If not check the wrong return value of it, lead to function `ping_rcv` return success. Signed-off-by:
Zheng Yongjun <zhengyongjun3@huawei.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Johannes Berg authored
[ Upstream commit a9799541 ] These are not permitted by the spec, just drop them. Link: https://lore.kernel.org/r/20210609161305.23def022b750.Ibd6dd3cdce573dae262fcdc47f8ac52b883a9c50@changeid Signed-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
-
Du Cheng authored
[ Upstream commit a64b6a25 ] If the userland switches back-and-forth between NL80211_IFTYPE_OCB and NL80211_IFTYPE_ADHOC via send_msg(NL80211_CMD_SET_INTERFACE), there is a chance where the cleanup cfg80211_leave_ocb() is not called. This leads to initialization of in-use memory (e.g. init u.ibss while in-use by u.ocb) due to a shared struct/union within ieee80211_sub_if_data: struct ieee80211_sub_if_data { ... union { struct ieee80211_if_ap ap; struct ieee80211_if_vlan vlan; struct ieee80211_if_managed mgd; struct ieee80211_if_ibss ibss; // <- shares address struct ieee80211_if_mesh mesh; struct ieee80211_if_ocb ocb; // <- shares address struct ieee80211_if_mntr mntr; struct ieee80211_if_nan nan; } u; ... } Therefore add handling of otype == NL80211_IFTYPE_OCB, during cfg80211_change_iface() to perform cleanup when leaving OCB mode. link to syzkaller bug: https://syzkaller.appspot.com/bug?id=0612dbfa595bf4b9b680ff7b4948257b8e3732d5 Reported-by: syzbot+105896fac213f26056f9@syzkaller.appspotmail.com Signed-off-by:
Du Cheng <ducheng2@gmail.com> Link: https://lore.kernel.org/r/20210428063941.105161-1-ducheng2@gmail.com Signed-off-by:
-
Johannes Berg authored
[ Upstream commit 0ee4d555 ] Syzbot reports that it's possible to hit this from userspace, by trying to add a station before any other connection setup has been done. Instead of trying to catch this in some other way simply remove the warning, that will appropriately reject the call from userspace. Reported-by: syzbot+7716dbc401d9a437890d@syzkaller.appspotmail.com Link: https://lore.kernel.org/r/20210517164715.f537da276d17.Id05f40ec8761d6a8cc2df87f1aa09c651988a586@changeid Signed-off-by:
-
Rafael J. Wysocki authored
[ Upstream commit 4d6035f9 ] Revert commit 4514d991 ("PCI: PM: Do not read power state in pci_enable_device_flags()") that is reported to cause PCI device initialization issues on some systems. BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=213481 Link: https://lore.kernel.org/linux-acpi/YNDoGICcg0V8HhpQ@eldamar.lan Reported-by:
Michael <phyre@rogers.com> Reported-by:
Salvatore Bonaccorso <carnil@debian.org> Fixes: 4514d991 ("PCI: PM: Do not read power state in pci_enable_device_flags()") Signed-off-by:
Rafael J. Wysocki <rafael.j.wysocki@intel.com> Signed-off-by:
-
Suzuki K Poulose authored
commit 3cce50df upstream. The arm64 PMU updates the event counters and reprograms the counters in the overflow IRQ handler without disabling the PMU. This could potentially cause skews in for group counters, where the overflowed counters may potentially loose some event counts, while they are reprogrammed. To prevent this, disable the PMU while we process the counter overflows and enable it right back when we are done. This patch also moves the PMU stop/start routines to avoid a forward declaration. Suggested-by:
Mark Rutland <mark.rutland@arm.com> Cc: Will Deacon <will.deacon@arm.com> Acked-by:
Suzuki K Poulose <suzuki.poulose@arm.com> Signed-off-by:
Will Deacon <will.deacon@arm.com> Signed-off-by:
Aman Priyadarshi <apeureka@amazon.de> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Nathan Chancellor authored
commit e607ff63 upstream. With the latest mkimage from U-Boot 2021.04, the generic defconfigs no longer build, failing with: /usr/bin/mkimage: verify_header failed for FIT Image support with exit code 1 This is expected after the linked U-Boot commits because '@' is forbidden in the node names due to the way that libfdt treats nodes with the same prefix but different unit addresses. Switch the '@' in the node name to '-'. Drop the unit addresses from the hash and kernel child nodes because there is only one node so they do not need to have a number to differentiate them. Cc: stable@vger.kernel.org Link: https://source.denx.de/u-boot/u-boot/-/commit/79af75f7776fc20b0d7eb6afe1e27c00fdb4b9b4 Link: https://source.denx.de/u-boot/u-boot/-/commit/3f04db891a353f4b127ed57279279f851c6b4917 Suggested-by:
Simon Glass <sjg@chromium.org> Signed-off-by:
Nathan Chancellor <nathan@kernel.org> Reviewed-by:
Tom Rini <trini@konsulko.com> Signed-off-by:
Thomas Bogendoerfer <tsbogend@alpha.franken.de> [nathan: Backport to 4.14, only apply to .its.S files that exist] Signed-off-by:
-
Nathan Chancellor authored
commit 885480b0 upstream. Currently, -Wunused-but-set-variable is only supported by GCC so it is disabled unconditionally in a GCC only block (it is enabled with W=1). clang currently has its implementation for this warning in review so preemptively move this statement out of the GCC only block and wrap it with cc-disable-warning so that both compilers function the same. Cc: stable@vger.kernel.org Link: https://reviews.llvm.org/D100581 Signed-off-by:
Nick Desaulniers <ndesaulniers@google.com> Tested-by:
Masahiro Yamada <masahiroy@kernel.org> [nc: Backport, workaround lack of e2079e93 in older branches] Signed-off-by:
-
Arnd Bergmann authored
commit dad7b989 upstream. When building the kernel wtih gcc-10 or higher using the CONFIG_CC_OPTIMIZE_FOR_PERFORMANCE=y flag, the compiler picks a slightly different set of registers for the inline assembly in cpu_init() that subsequently results in a corrupt kernel stack as well as remaining in FIQ mode. If a banked register is used for the last argument, the wrong version of that register gets loaded into CPSR_c. When building in Arm mode, the arguments are passed as immediate values and the bug cannot happen. This got introduced when Daniel reworked the FIQ handling and was technically always broken, but happened to work with both clang and gcc before gcc-10 as long as they picked one of the lower registers. This is probably an indication that still very few people build the kernel in Thumb2 mode. Marek pointed out the problem on IRC, Arnd narrowed it down to this inline assembly and Russell pinpointed the exact bug. Change the constraints to force the final mode switch to use a non-banked register for the argument to ensure that the correct constant gets loaded. Another alternative would be to always use registers for the constant arguments to avoid the #ifdef that has now become more complex. Cc: <stable@vger.kernel.org> # v3.18+ Cc: Daniel Thompson <daniel.thompson@linaro.org> Reported-by:
Marek Vasut <marek.vasut@gmail.com> Acked-by:
Ard Biesheuvel <ardb@kernel.org> Fixes: c0e7f7ee ("ARM: 8150/3: fiq: Replace default FIQ handler") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by:
-
Christian König authored
commit 4b41726a upstream. We actually need to wait for the moving fence after pinning the BO to make sure that the pin is completed. Signed-off-by:
Christian König <christian.koenig@amd.com> Reviewed-by:
Daniel Vetter <daniel.vetter@ffwll.ch> References: https://lore.kernel.org/dri-devel/20210621151758.2347474-1-daniel.vetter@ffwll.ch/ CC: stable@kernel.org Link: https://patchwork.freedesktop.org/patch/msgid/20210622114506.106349-2-christian.koenig@amd.com Signed-off-by:
-
Christian König authored
commit 17b11f71 upstream. We actually need to wait for the moving fence after pinning the BO to make sure that the pin is completed. v2: grab the lock while waiting Signed-off-by:
-
Thomas Gleixner authored
commit efa16550 upstream. If access_ok() or fpregs_soft_set() fails in __fpu__restore_sig() then the function just returns but does not clear the FPU state as it does for all other fatal failures. Clear the FPU state for these failures as well. Fixes: 72a671ce ("x86, fpu: Unify signal handling code paths for x86 and x86_64 kernels") Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
Borislav Petkov <bp@suse.de> Cc: stable@vger.kernel.org Link: https://lkml.kernel.org/r/87mtryyhhz.ffs@nanos.tec.linutronix.de Signed-off-by:
-
Al Viro authored
commit 7b745a4e upstream. new_sb is left uninitialized in case of early failures in kernfs_mount_ns(), and while IS_ERR(root) is true in all such cases, using IS_ERR(root) || !new_sb is not a solution - IS_ERR(root) is true in some cases when new_sb is true. Make sure new_sb is initialized (and matches the reality) in all cases and fix the condition for dropping kobj reference - we want it done precisely in those situations where the reference has not been transferred into a new super_block instance. Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> Signed-off-by:
Guilherme G. Piccoli <gpiccoli@canonical.com> Signed-off-by:
-
Al Viro authored
commit 82382ace upstream. make sure that info->node is initialized early, so that kernfs_kill_sb() can list_del() it safely. Signed-off-by:
-
Peter Chen authored
commit 4bf584a0 upstream. When do system reboot, it calls dwc3_shutdown and the whole debugfs for dwc3 has removed first, when the gadget tries to do deinit, and remove debugfs for its endpoints, it meets NULL pointer dereference issue when call debugfs_lookup. Fix it by removing the whole dwc3 debugfs later than dwc3_drd_exit. [ 2924.958838] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000002 .... [ 2925.030994] pstate: 60000005 (nZCv daif -PAN -UAO -TCO BTYPE=--) [ 2925.037005] pc : inode_permission+0x2c/0x198 [ 2925.041281] lr : lookup_one_len_common+0xb0/0xf8 [ 2925.045903] sp : ffff80001276ba70 [ 2925.049218] x29: ffff80001276ba70 x28: ffff0000c01f0000 x27: 0000000000000000 [ 2925.056364] x26: ffff800011791e70 x25: 0000000000000008 x24: dead000000000100 [ 2925.063510] x23: dead000000000122 x22: 0000000000000000 x21: 0000000000000001 [ 2925.070652] x20: ffff8000122c6188 x19: 0000000000000000 x18: 0000000000000000 [ 2925.077797] x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000004 [ 2925.084943] x14: ffffffffffffffff x13: 0000000000000000 x12: 0000000000000030 [ 2925.092087] x11: 0101010101010101 x10: 7f7f7f7f7f7f7f7f x9 : ffff8000102b2420 [ 2925.099232] x8 : 7f7f7f7f7f7f7f7f x7 : feff73746e2f6f64 x6 : 0000000000008080 [ 2925.106378] x5 : 61c8864680b583eb x4 : 209e6ec2d263dbb7 x3 : 000074756f307065 [ 2925.113523] x2 : 0000000000000001 x1 : 0000000000000000 x0 : ffff8000122c6188 [ 2925.120671] Call trace: [ 2925.123119] inode_permission+0x2c/0x198 [ 2925.127042] lookup_one_len_common+0xb0/0xf8 [ 2925.131315] lookup_one_len_unlocked+0x34/0xb0 [ 2925.135764] lookup_positive_unlocked+0x14/0x50 [ 2925.140296] debugfs_lookup+0x68/0xa0 [ 2925.143964] dwc3_gadget_free_endpoints+0x84/0xb0 [ 2925.148675] dwc3_gadget_exit+0x28/0x78 [ 2925.152518] dwc3_drd_exit+0x100/0x1f8 [ 2925.156267] dwc3_remove+0x11c/0x120 [ 2925.159851] dwc3_shutdown+0x14/0x20 [ 2925.163432] platform_shutdown+0x28/0x38 [ 2925.167360] device_shutdown+0x15c/0x378 [ 2925.171291] kernel_restart_prepare+0x3c/0x48 [ 2925.175650] kernel_restart+0x1c/0x68 [ 2925.179316] __do_sys_reboot+0x218/0x240 [ 2925.183247] __arm64_sys_reboot+0x28/0x30 [ 2925.187262] invoke_syscall+0x48/0x100 [ 2925.191017] el0_svc_common.constprop.0+0x48/0xc8 [ 2925.195726] do_el0_svc+0x28/0x88 [ 2925.199045] el0_svc+0x20/0x30 [ 2925.202104] el0_sync_handler+0xa8/0xb0 [ 2925.205942] el0_sync+0x148/0x180 [ 2925.209270] Code: a9025bf5 2a0203f5 121f0056 370802b5 (79400660) [ 2925.215372] ---[ end trace 124254d8e485a58b ]--- [ 2925.220012] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b [ 2925.227676] Kernel Offset: disabled [ 2925.231164] CPU features: 0x00001001,20000846 [ 2925.235521] Memory Limit: none [ 2925.238580] ---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b ]--- Fixes: 8d396bb0 ("usb: dwc3: debugfs: Add and remove endpoint dirs dynamically") Cc: Jack Pham <jackp@codeaurora.org> Tested-by:
Jack Pham <jackp@codeaurora.org> Signed-off-by:
Peter Chen <peter.chen@kernel.org> Link: https://lore.kernel.org/r/20210608105656.10795-1-peter.chen@kernel.org (cherry picked from commit 2a042767) Link: https://lore.kernel.org/r/20210615080847.GA10432@jackp-linux.qualcomm.com Signed-off-by:
-
Eric Dumazet authored
commit aa6dd211 upstream. In commit 73f156a6 ("inetpeer: get rid of ip_id_count") I used a very small hash table that could be abused by patient attackers to reveal sensitive information. Switch to a dynamic sizing, depending on RAM size. Typical big hosts will now use 128x more storage (2 MB) to get a similar increase in security and reduction of hash collisions. As a bonus, use of alloc_large_system_hash() spreads allocated memory among all NUMA nodes. Fixes: 73f156a6 ("inetpeer: get rid of ip_id_count") Reported-by:
Amit Klein <aksecurity@gmail.com> Signed-off-by:
Eric Dumazet <edumazet@google.com> Cc: Willy Tarreau <w@1wt.eu> Signed-off-by:
-
Tetsuo Handa authored
commit 8d0caedb upstream. syzbot is reporting hung task at register_netdevice_notifier() [1] and unregister_netdevice_notifier() [2], for cleanup_net() might perform time consuming operations while CAN driver's raw/bcm/isotp modules are calling {register,unregister}_netdevice_notifier() on each socket. Change raw/bcm/isotp modules to call register_netdevice_notifier() from module's __init function and call unregister_netdevice_notifier() from module's __exit function, as with gw/j1939 modules are doing. Link: https://syzkaller.appspot.com/bug?id=391b9498827788b3cc6830226d4ff5be87107c30 [1] Link: https://syzkaller.appspot.com/bug?id=1724d278c83ca6e6df100a2e320c10d991cf2bce [2] Link: https://lore.kernel.org/r/54a5f451-05ed-f977-8534-79e7aa2bcc8f@i-love.sakura.ne.jp Cc: linux-stable <stable@vger.kernel.org> Reported-by:
syzbot <syzbot+355f8edb2ff45d5f95fa@syzkaller.appspotmail.com> Reported-by:
syzbot <syzbot+0f1827363a305f74996f@syzkaller.appspotmail.com> Reviewed-by:
Kirill Tkhai <ktkhai@virtuozzo.com> Tested-by:
Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by:
Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Fugang Duan authored
commit cb3cefe3 upstream. Add clock rate zero check to fix coverity issue of "divide by 0". Fixes: commit 85bd1798 ("net: fec: fix spin_lock dead lock") Signed-off-by:
Fugang Duan <fugang.duan@nxp.com> Signed-off-by:
Joakim Zhang <qiangqing.zhang@nxp.com> Signed-off-by:
-
Andrew Morton authored
commit 1b3865d0 upstream. Fixes build with CONFIG_SLAB_FREELIST_HARDENED=y. Hopefully. But it's the right thing to do anwyay. Fixes: 1ad53d9f ("slub: improve bit diffusion for freelist ptr obfuscation") Link: https://bugzilla.kernel.org/show_bug.cgi?id=213417 Reported-by: <vannguye@cisco.com> Acked-by:
Kees Cook <keescook@chromium.org> Cc: <stable@vger.kernel.org> Signed-off-by:
Andrew Morton <akpm@linux-foundation.org> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by:
-
Nikolay Aleksandrov authored
commit cfc579f9 upstream. The egress tunnel code uses dst_clone() and directly sets the result which is wrong because the entry might have 0 refcnt or be already deleted, causing number of problems. It also triggers the WARN_ON() in dst_hold()[1] when a refcnt couldn't be taken. Fix it by using dst_hold_safe() and checking if a reference was actually taken before setting the dst. [1] dmesg WARN_ON log and following refcnt errors WARNING: CPU: 5 PID: 38 at include/net/dst.h:230 br_handle_egress_vlan_tunnel+0x10b/0x134 [bridge] Modules linked in: 8021q garp mrp bridge stp llc bonding ipv6 virtio_net CPU: 5 PID: 38 Comm: ksoftirqd/5 Kdump: loaded Tainted: G W 5.13.0-rc3+ #360 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-1.fc33 04/01/2014 RIP: 0010:br_handle_egress_vlan_tunnel+0x10b/0x134 [bridge] Code: e8 85 bc 01 e1 45 84 f6 74 90 45 31 f6 85 db 48 c7 c7 a0 02 19 a0 41 0f 94 c6 31 c9 31 d2 44 89 f6 e8 64 bc 01 e1 85 db 75 02 <0f> 0b 31 c9 31 d2 44 89 f6 48 c7 c7 70 02 19 a0 e8 4b bc 01 e1 49 RSP: 0018:ffff8881003d39e8 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000000 RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffffffffa01902a0 RBP: ffff8881040c6700 R08: 0000000000000000 R09: 0000000000000001 R10: 2ce93d0054fe0d00 R11: 54fe0d00000e0000 R12: ffff888109515000 R13: 0000000000000000 R14: 0000000000000001 R15: 0000000000000401 FS: 0000000000000000(0000) GS:ffff88822bf40000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f42ba70f030 CR3: 0000000109926000 CR4: 00000000000006e0 Call Trace: br_handle_vlan+0xbc/0xca [bridge] __br_forward+0x23/0x164 [bridge] deliver_clone+0x41/0x48 [bridge] br_handle_frame_finish+0x36f/0x3aa [bridge] ? skb_dst+0x2e/0x38 [bridge] ? br_handle_ingress_vlan_tunnel+0x3e/0x1c8 [bridge] ? br_handle_frame_finish+0x3aa/0x3aa [bridge] br_handle_frame+0x2c3/0x377 [bridge] ? __skb_pull+0x33/0x51 ? vlan_do_receive+0x4f/0x36a ? br_handle_frame_finish+0x3aa/0x3aa [bridge] __netif_receive_skb_core+0x539/0x7c6 ? __list_del_entry_valid+0x16e/0x1c2 __netif_receive_skb_list_core+0x6d/0xd6 netif_receive_skb_list_internal+0x1d9/0x1fa gro_normal_list+0x22/0x3e dev_gro_receive+0x55b/0x600 ? detach_buf_split+0x58/0x140 napi_gro_receive+0x94/0x12e virtnet_poll+0x15d/0x315 [virtio_net] __napi_poll+0x2c/0x1c9 net_rx_action+0xe6/0x1fb __do_softirq+0x115/0x2d8 run_ksoftirqd+0x18/0x20 smpboot_thread_fn+0x183/0x19c ? smpboot_unregister_percpu_thread+0x66/0x66 kthread+0x10a/0x10f ? kthread_mod_delayed_work+0xb6/0xb6 ret_from_fork+0x22/0x30 ---[ end trace 49f61b07f775fd2b ]--- dst_release: dst:00000000c02d677a refcnt:-1 dst_release underflow Cc: stable@vger.kernel.org Fixes: 11538d03 ("bridge: vlan dst_metadata hooks in ingress and egress paths") Signed-off-by:
Nikolay Aleksandrov <nikolay@nvidia.com> Signed-off-by:
-
Nikolay Aleksandrov authored
commit 58e20717 upstream. This patch fixes a tunnel_dst null pointer dereference due to lockless access in the tunnel egress path. When deleting a vlan tunnel the tunnel_dst pointer is set to NULL without waiting a grace period (i.e. while it's still usable) and packets egressing are dereferencing it without checking. Use READ/WRITE_ONCE to annotate the lockless use of tunnel_id, use RCU for accessing tunnel_dst and make sure it is read only once and checked in the egress path. The dst is already properly RCU protected so we don't need to do anything fancy than to make sure tunnel_id and tunnel_dst are read only once and checked in the egress path. Cc: stable@vger.kernel.org Fixes: 11538d03 ("bridge: vlan dst_metadata hooks in ingress and egress paths") Signed-off-by:
-
Bumyong Lee authored
commit 4ad5dd2d upstream. flags varible which is the input parameter of pl330_prep_dma_cyclic() should not be used by spinlock_irq[save/restore] function. Signed-off-by:
Jongho Park <jongho7.park@samsung.com> Signed-off-by:
Bumyong Lee <bumyong.lee@samsung.com> Signed-off-by:
Chanho Park <chanho61.park@samsung.com> Link: https://lore.kernel.org/r/20210507063647.111209-1-chanho61.park@samsung.com Fixes: f6f2421c ("dmaengine: pl330: Merge dma_pl330_dmac and pl330_dmac structs") Cc: stable@vger.kernel.org Signed-off-by:
Vinod Koul <vkoul@kernel.org> Signed-off-by:
-
Vineet Gupta authored
commit 96f1b001 upstream. ARCv2 has some configuration dependent registers (r30, r58, r59) which could be targetted by the compiler. To keep the ABI stable, these were unconditionally part of the glibc ABI (sysdeps/unix/sysv/linux/arc/sys/ucontext.h:mcontext_t) however we missed populating them (by saving/restoring them across signal handling). This patch fixes the issue by - adding arcv2 ABI regs to kernel struct sigcontext - populating them during signal handling Change to struct sigcontext might seem like a glibc ABI change (although it primarily uses ucontext_t:mcontext_t) but the fact is - it has only been extended (existing fields are not touched) - the old sigcontext was ABI incomplete to begin with anyways Fixes: https://github.com/foss-for-synopsys-dwc-arc-processors/linux/issues/53 Cc: <stable@vger.kernel.org> Tested-by:
kernel test robot <lkp@intel.com> Reported-by:
Vladimir Isaev <isaev@synopsys.com> Signed-off-by:
Vineet Gupta <vgupta@synopsys.com> Signed-off-by:
-
Chiqijun authored
commit ce00322c upstream. pcie_flr() starts a Function Level Reset (FLR), waits 100ms (the maximum time allowed for FLR completion by PCIe r5.0, sec 6.6.2), and waits for the FLR to complete. It assumes the FLR is complete when a config read returns valid data. When we do an FLR on several Huawei Intelligent NIC VFs at the same time, firmware on the NIC processes them serially. The VF may respond to config reads before the firmware has completed its reset processing. If we bind a driver to the VF (e.g., by assigning the VF to a virtual machine) in the interval between the successful config read and completion of the firmware reset processing, the NIC VF driver may fail to load. Prevent this driver failure by waiting for the NIC firmware to complete its reset processing. Not all NIC firmware supports this feature. [bhelgaas: commit log] Link: https://support.huawei.com/enterprise/en/doc/EDOC1100063073/87950645/vm-oss-occasionally-fail-to-load-the-in200-driver-when-the-vf-performs-flr Link: https://lore.kernel.org/r/20210414132301.1793-1-chiqijun@huawei.com Signed-off-by:
Chiqijun <chiqijun@huawei.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> Reviewed-by:
Alex Williamson <alex.williamson@redhat.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Sriharsha Basavapatna authored
commit db2f77e2 upstream. The Broadcom BCM57414 NIC may be a multi-function device. While it does not advertise an ACS capability, peer-to-peer transactions are not possible between the individual functions, so it is safe to treat them as fully isolated. Add an ACS quirk for this device so the functions can be in independent IOMMU groups and attached individually to userspace applications using VFIO. [bhelgaas: commit log] Link: https://lore.kernel.org/r/1621645997-16251-1-git-send-email-michael.chan@broadcom.com Signed-off-by:
Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com> Signed-off-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
-
Shanker Donthineni authored
commit 4c207e71 upstream. Some NVIDIA GPU devices do not work with SBR. Triggering SBR leaves the device inoperable for the current system boot. It requires a system hard-reboot to get the GPU device back to normal operating condition post-SBR. For the affected devices, enable NO_BUS_RESET quirk to avoid the issue. This issue will be fixed in the next generation of hardware. Link: https://lore.kernel.org/r/20210608054857.18963-8-ameynarkhede03@gmail.com Signed-off-by:
Shanker Donthineni <sdonthineni@nvidia.com> Signed-off-by:
Sinan Kaya <okaya@kernel.org> Cc: stable@vger.kernel.org Signed-off-by:
-
Antti Järvinen authored
commit b5cf198e upstream. Some TI KeyStone C667X devices do not support bus/hot reset. The PCIESS automatically disables LTSSM when Secondary Bus Reset is received and device stops working. Prevent bus reset for these devices. With this change, the device can be assigned to VMs with VFIO, but it will leak state between VMs. Reference: https://e2e.ti.com/support/processors/f/791/t/954382 Link: https://lore.kernel.org/r/20210315102606.17153-1-antti.jarvinen@gmail.com Signed-off-by:
Antti Järvinen <antti.jarvinen@gmail.com> Signed-off-by:
Kishon Vijay Abraham I <kishon@ti.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Steven Rostedt (VMware) authored
commit 89529d8b upstream. The trace_clock_global() tries to make sure the events between CPUs is somewhat in order. A global value is used and updated by the latest read of a clock. If one CPU is ahead by a little, and is read by another CPU, a lock is taken, and if the timestamp of the other CPU is behind, it will simply use the other CPUs timestamp. The lock is also only taken with a "trylock" due to tracing, and strange recursions can happen. The lock is not taken at all in NMI context. In the case where the lock is not able to be taken, the non synced timestamp is returned. But it will not be less than the saved global timestamp. The problem arises because when the time goes "backwards" the time returned is the saved timestamp plus 1. If the lock is not taken, and the plus one to the timestamp is returned, there's a small race that can cause the time to go backwards! CPU0 CPU1 ---- ---- trace_clock_global() { ts = clock() [ 1000 ] trylock(clock_lock) [ success ] global_ts = ts; [ 1000 ] <interrupted by NMI> trace_clock_global() { ts = clock() [ 999 ] if (ts < global_ts) ts = global_ts + 1 [ 1001 ] trylock(clock_lock) [ fail ] return ts [ 1001] } unlock(clock_lock); return ts; [ 1000 ] } trace_clock_global() { ts = clock() [ 1000 ] if (ts < global_ts) [ false 1000 == 1000 ] trylock(clock_lock) [ success ] global_ts = ts; [ 1000 ] unlock(clock_lock) return ts; [ 1000 ] } The above case shows to reads of trace_clock_global() on the same CPU, but the second read returns one less than the first read. That is, time when backwards, and this is not what is allowed by trace_clock_global(). This was triggered by heavy tracing and the ring buffer checker that tests for the clock going backwards: Ring buffer clock went backwards: 20613921464 -> 20613921463 ------------[ cut here ]------------ WARNING: CPU: 2 PID: 0 at kernel/trace/ring_buffer.c:3412 check_buffer+0x1b9/0x1c0 Modules linked in: [..] [CPU: 2]TIME DOES NOT MATCH expected:20620711698 actual:20620711697 delta:6790234 before:20613921463 after:20613921463 [20613915818] PAGE TIME STAMP [20613915818] delta:0 [20613915819] delta:1 [20613916035] delta:216 [20613916465] delta:430 [20613916575] delta:110 [20613916749] delta:174 [20613917248] delta:499 [20613917333] delta:85 [20613917775] delta:442 [20613917921] delta:146 [20613918321] delta:400 [20613918568] delta:247 [20613918768] delta:200 [20613919306] delta:538 [20613919353] delta:47 [20613919980] delta:627 [20613920296] delta:316 [20613920571] delta:275 [20613920862] delta:291 [20613921152] delta:290 [20613921464] delta:312 [20613921464] delta:0 TIME EXTEND [20613921464] delta:0 This happened more than once, and always for an off by one result. It also started happening after commit aafe104a was added. Cc: stable@vger.kernel.org Fixes: aafe104a ("tracing: Restructure trace_clock_global() to never block") Signed-off-by:
Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by:
-
Steven Rostedt (VMware) authored
commit 4fdd595e upstream. A while ago, when the "trace" file was opened, tracing was stopped, and code was added to stop recording the comms to saved_cmdlines, for mapping of the pids to the task name. Code has been added that only records the comm if a trace event occurred, and there's no reason to not trace it if the trace file is opened. Cc: stable@vger.kernel.org Fixes: 7ffbd48d ("tracing: Cache comms only after an event occurred") Signed-off-by:
-
Steven Rostedt (VMware) authored
commit 85550c83 upstream. The saved_cmdlines is used to map pids to the task name, such that the output of the tracing does not just show pids, but also gives a human readable name for the task. If the name is not mapped, the output looks like this: <...>-1316 [005] ...2 132.044039: ... Instead of this: gnome-shell-1316 [005] ...2 132.044039: ... The names are updated when tracing is running, but are skipped if tracing is stopped. Unfortunately, this stops the recording of the names if the top level tracer is stopped, and not if there's other tracers active. The recording of a name only happens when a new event is written into a ring buffer, so there is no need to test if tracing is on or not. If tracing is off, then no event is written and no need to test if tracing is off or not. Remove the check, as it hides the names of tasks for events in the instance buffers. Cc: stable@vger.kernel.org Fixes: 7ffbd48d ("tracing: Cache comms only after an event occurred") Signed-off-by:
-
Andrew Lunn authored
commit a7d8d1c7 upstream. The Cypress CY7C65632 appears to have an issue with auto suspend and detecting devices, not too dissimilar to the SMSC 5534B hub. It is easiest to reproduce by connecting multiple mass storage devices to the hub at the same time. On a Lenovo Yoga, around 1 in 3 attempts result in the devices not being detected. It is however possible to make them appear using lsusb -v. Disabling autosuspend for this hub resolves the issue. Fixes: 1208f9e1 ("USB: hub: Fix the broken detection of USB3 device in SMSC hub") Cc: stable@vger.kernel.org Signed-off-by:
Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20210614155524.2228800-1-andrew@lunn.ch Signed-off-by:
-
Pavel Skripkin authored
commit 91c02557 upstream. Syzbot reported memory leak in SocketCAN driver for Microchip CAN BUS Analyzer Tool. The problem was in unfreed usb_coherent. In mcba_usb_start() 20 coherent buffers are allocated and there is nothing, that frees them: 1) In callback function the urb is resubmitted and that's all 2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER is not set (see mcba_usb_start) and this flag cannot be used with coherent buffers. Fail log: | [ 1354.053291][ T8413] mcba_usb 1-1:0.0 can0: device disconnected | [ 1367.059384][ T8420] kmemleak: 20 new suspected memory leaks (see /sys/kernel/debug/kmem) So, all allocated buffers should be freed with usb_free_coherent() explicitly NOTE: The same pattern for allocating and freeing coherent buffers is used in drivers/net/can/usb/kvaser_usb/kvaser_usb_core.c Fixes: 51f3baad ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer") Link: https://lore.kernel.org/r/20210609215833.30393-1-paskripkin@gmail.com Cc: linux-stable <stable@vger.kernel.org> Reported-and-tested-by: syzbot+57281c762a3922e14dfe@syzkaller.appspotmail.com Signed-off-by:
Pavel Skripkin <paskripkin@gmail.com> Signed-off-by:
-
Norbert Slusarek authored
commit 5e87ddbe upstream. On 64-bit systems, struct bcm_msg_head has an added padding of 4 bytes between struct members count and ival1. Even though all struct members are initialized, the 4-byte hole will contain data from the kernel stack. This patch zeroes out struct bcm_msg_head before usage, preventing infoleaks to userspace. Fixes: ffd980f9 ("[CAN]: Add broadcast manager (bcm) protocol") Link: https://lore.kernel.org/r/trinity-7c1b2e82-e34f-4885-8060-2cd7a13769ce-1623532166177@3c-app-gmx-bs52 Cc: linux-stable <stable@vger.kernel.org> Signed-off-by:
Norbert Slusarek <nslusarek@gmx.net> Acked-by:
-
Riwen Lu authored
[ Upstream commit 78d13552 ] The scpi hwmon shows the sub-zero temperature in an unsigned integer, which would confuse the users when the machine works in low temperature environment. This shows the sub-zero temperature in an signed value and users can get it properly from sensors. Signed-off-by:
Riwen Lu <luriwen@kylinos.cn> Tested-by:
Xin Chen <chenxin@kylinos.cn> Link: https://lore.kernel.org/r/20210604030959.736379-1-luriwen@kylinos.cn Signed-off-by:
Guenter Roeck <linux@roeck-us.net> Signed-off-by:
-
Chen Li authored
[ Upstream commit ab8363d3 ] I met a gpu addr bug recently and the kernel log tells me the pc is memcpy/memset and link register is radeon_uvd_resume. As we know, in some architectures, optimized memcpy/memset may not work well on device memory. Trival memcpy_toio/memset_io can fix this problem. BTW, amdgpu has already done it in: commit ba0b2275 ("drm/amdgpu: use memcpy_to/fromio for UVD fw upload"), that's why it has no this issue on the same gpu and platform. Signed-off-by:
Chen Li <chenli@uniontech.com> Reviewed-by:
Alex Deucher <alexander.deucher@amd.com> Signed-off-by:
-
Pavel Skripkin authored
[ Upstream commit 9cca0c2d ] static void ec_bhf_remove(struct pci_dev *dev) { ... struct ec_bhf_priv *priv = netdev_priv(net_dev); unregister_netdev(net_dev); free_netdev(net_dev); pci_iounmap(dev, priv->dma_io); pci_iounmap(dev, priv->io); ... } priv is netdev private data, but it is used after free_netdev(). It can cause use-after-free when accessing priv pointer. So, fix it by moving free_netdev() after pci_iounmap() calls. Fixes: 6af55ff5 ("Driver for Beckhoff CX5020 EtherCAT master module.") Signed-off-by:
-
Toke Høiland-Jørgensen authored
[ Upstream commit 32182747 ] When constructing ICMP response messages, the kernel will try to pick a suitable source address for the outgoing packet. However, if no IPv4 addresses are configured on the system at all, this will fail and we end up producing an ICMP message with a source address of 0.0.0.0. This can happen on a box routing IPv4 traffic via v6 nexthops, for instance. Since 0.0.0.0 is not generally routable on the internet, there's a good chance that such ICMP messages will never make it back to the sender of the original packet that the ICMP message was sent in response to. This, in turn, can create connectivity and PMTUd problems for senders. Fortunately, RFC7600 reserves a dummy address to be used as a source for ICMP messages (192.0.0.8/32), so let's teach the kernel to substitute that address as a last resort if the regular source address selection procedure fails. Below is a quick example reproducing this issue with network namespaces: ip netns add ns0 ip l add type veth peer netns ns0 ip l set dev veth0 up ip a add 10.0.0.1/24 dev veth0 ip a add fc00:dead:cafe:42::1/64 dev veth0 ip r add 10.1.0.0/24 via inet6 fc00:dead:cafe:42::2 ip -n ns0 l set dev veth0 up ip -n ns0 a add fc00:dead:cafe:42::2/64 dev veth0 ip -n ns0 r add 10.0.0.0/24 via inet6 fc00:dead:cafe:42::1 ip netns exec ns0 sysctl -w net.ipv4.icmp_ratelimit=0 ip netns exec ns0 sysctl -w net.ipv4.ip_forward=1 tcpdump -tpni veth0 -c 2 icmp & ping -w 1 10.1.0.1 > /dev/null tcpdump: verbose output suppressed, use -v[v]... for full protocol decode listening on veth0, link-type EN10MB (Ethernet), snapshot length 262144 bytes IP 10.0.0.1 > 10.1.0.1: ICMP echo request, id 29, seq 1, length 64 IP 0.0.0.0 > 10.0.0.1: ICMP net 10.1.0.1 unreachable, length 92 2 packets captured 2 packets received by filter 0 packets dropped by kernel With this patch the above capture changes to: IP 10.0.0.1 > 10.1.0.1: ICMP echo request, id 31127, seq 1, length 64 IP 192.0.0.8 > 10.0.0.1: ICMP net 10.1.0.1 unreachable, length 92 Fixes: 1da177e4 ("Linux-2.6.12-rc2") Reported-by:
Juliusz Chroboczek <jch@irif.fr> Reviewed-by:
David Ahern <dsahern@kernel.org> Signed-off-by:
Toke Høiland-Jørgensen <toke@redhat.com> Signed-off-by:
-
Linyu Yuan authored
[ Upstream commit c3b26fdf ] when usbnet transmit a skb, eem fixup it in eem_tx_fixup(), if skb_copy_expand() failed, it return NULL, usbnet_start_xmit() will have no chance to free original skb. fix it by free orginal skb in eem_tx_fixup() first, then check skb clone status, if failed, return NULL to usbnet. Fixes: 9f722c09 ("usbnet: CDC EEM support (v5)") Signed-off-by:
Linyu Yuan <linyyuan@codeaurora.org> Reviewed-by:
-
Pavel Skripkin authored
[ Upstream commit 7edcc682 ] My local syzbot instance hit memory leak in mkiss_open()[1]. The problem was in missing free_netdev() in mkiss_close(). In mkiss_open() netdevice is allocated and then registered, but in mkiss_close() netdevice was only unregistered, but not freed. Fail log: BUG: memory leak unreferenced object 0xffff8880281ba000 (size 4096): comm "syz-executor.1", pid 11443, jiffies 4295046091 (age 17.660s) hex dump (first 32 bytes): 61 78 30 00 00 00 00 00 00 00 00 00 00 00 00 00 ax0............. 00 27 fa 2a 80 88 ff ff 00 00 00 00 00 00 00 00 .'.*............ backtrace: [<ffffffff81a27201>] kvmalloc_node+0x61/0xf0 [<ffffffff8706e7e8>] alloc_netdev_mqs+0x98/0xe80 [<ffffffff84e64192>] mkiss_open+0xb2/0x6f0 [1] [<ffffffff842355db>] tty_ldisc_open+0x9b/0x110 [<ffffffff84236488>] tty_set_ldisc+0x2e8/0x670 [<ffffffff8421f7f3>] tty_ioctl+0xda3/0x1440 [<ffffffff81c9f273>] __x64_sys_ioctl+0x193/0x200 [<ffffffff8911263a>] do_syscall_64+0x3a/0xb0 [<ffffffff89200068>] entry_SYSCALL_64_after_hwframe+0x44/0xae BUG: memory leak unreferenced object 0xffff8880141a9a00 (size 96): comm "syz-executor.1", pid 11443, jiffies 4295046091 (age 17.660s) hex dump (first 32 bytes): e8 a2 1b 28 80 88 ff ff e8 a2 1b 28 80 88 ff ff ...(.......(.... 98 92 9c aa b0 40 02 00 00 00 00 00 00 00 00 00 .....@.......... backtrace: [<ffffffff8709f68b>] __hw_addr_create_ex+0x5b/0x310 [<ffffffff8709fb38>] __hw_addr_add_ex+0x1f8/0x2b0 [<ffffffff870a0c7b>] dev_addr_init+0x10b/0x1f0 [<ffffffff8706e88b>] alloc_netdev_mqs+0x13b/0xe80 [<ffffffff84e64192>] mkiss_open+0xb2/0x6f0 [1] [<ffffffff842355db>] tty_ldisc_open+0x9b/0x110 [<ffffffff84236488>] tty_set_ldisc+0x2e8/0x670 [<ffffffff8421f7f3>] tty_ioctl+0xda3/0x1440 [<ffffffff81c9f273>] __x64_sys_ioctl+0x193/0x200 [<ffffffff8911263a>] do_syscall_64+0x3a/0xb0 [<ffffffff89200068>] entry_SYSCALL_64_after_hwframe+0x44/0xae BUG: memory leak unreferenced object 0xffff8880219bfc00 (size 512): comm "syz-executor.1", pid 11443, jiffies 4295046091 (age 17.660s) hex dump (first 32 bytes): 00 a0 1b 28 80 88 ff ff 80 8f b1 8d ff ff ff ff ...(............ 80 8f b1 8d ff ff ff ff 00 00 00 00 00 00 00 00 ................ backtrace: [<ffffffff81a27201>] kvmalloc_node+0x61/0xf0 [<ffffffff8706eec7>] alloc_netdev_mqs+0x777/0xe80 [<ffffffff84e64192>] mkiss_open+0xb2/0x6f0 [1] [<ffffffff842355db>] tty_ldisc_open+0x9b/0x110 [<ffffffff84236488>] tty_set_ldisc+0x2e8/0x670 [<ffffffff8421f7f3>] tty_ioctl+0xda3/0x1440 [<ffffffff81c9f273>] __x64_sys_ioctl+0x193/0x200 [<ffffffff8911263a>] do_syscall_64+0x3a/0xb0 [<ffffffff89200068>] entry_SYSCALL_64_after_hwframe+0x44/0xae BUG: memory leak unreferenced object 0xffff888029b2b200 (size 256): comm "syz-executor.1", pid 11443, jiffies 4295046091 (age 17.660s) hex dump (first 32 bytes): 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<ffffffff81a27201>] kvmalloc_node+0x61/0xf0 [<ffffffff8706f062>] alloc_netdev_mqs+0x912/0xe80 [<ffffffff84e64192>] mkiss_open+0xb2/0x6f0 [1] [<ffffffff842355db>] tty_ldisc_open+0x9b/0x110 [<ffffffff84236488>] tty_set_ldisc+0x2e8/0x670 [<ffffffff8421f7f3>] tty_ioctl+0xda3/0x1440 [<ffffffff81c9f273>] __x64_sys_ioctl+0x193/0x200 [<ffffffff8911263a>] do_syscall_64+0x3a/0xb0 [<ffffffff89200068>] entry_SYSCALL_64_after_hwframe+0x44/0xae Fixes: 815f62bf ("[PATCH] SMP rewrite of mkiss") Signed-off-by:
-
Christophe JAILLET authored
[ Upstream commit c19c8c0e ] If an error occurs after a 'pci_enable_pcie_error_reporting()' call, it must be undone by a corresponding 'pci_disable_pcie_error_reporting()' call, as already done in the remove function. Fixes: d6b6d987 ("be2net: use PCIe AER capability") Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Acked-by:
Somnath Kotur <somnath.kotur@broadcom.com> Signed-off-by:
-
