- 12 Jul, 2022 31 commits
-
-
Alison Schofield authored
commit 8a664875 upstream. CXL specification defines these as little endian. Fixes: 60b8f172 ("cxl/pmem: Translate NVDIMM label commands to CXL label commands") Reported-by:
Dan Williams <dan.j.williams@intel.com> Signed-off-by:
Alison Schofield <alison.schofield@intel.com> Link: https://lore.kernel.org/r/20220225221456.1025635-1-alison.schofield@intel.com Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Lu Baolu authored
commit 4140d77a upstream. The IOMMU driver shares the pasid table for PCI alias devices. When the RID2PASID entry of the shared pasid table has been filled by the first device, the subsequent device will encounter the "DMAR: Setup RID2PASID failed" failure as the pasid entry has already been marked as present. As the result, the IOMMU probing process will be aborted. On the contrary, when any alias device is hot-removed from the system, for example, by writing to /sys/bus/pci/devices/.../remove, the shared RID2PASID will be cleared without any notifications to other devices. As the result, any DMAs from those rest devices are blocked. Sharing pasid table among PCI alias devices could save two memory pages for devices underneath the PCIe-to-PCI bridges. Anyway, considering that those devices are rare on modern platforms that support VT-d in scalable mode and the saved memory is negligible, it's reasonable to remove this part of immature code to make the driver feasible and stable. Fixes: ef848b7e ("iommu/vt-d: Setup pasid entry for RID2PASID support") Reported-by:
Chenyi Qiang <chenyi.qiang@intel.com> Reported-by:
Ethan Zhao <haifeng.zhao@linux.intel.com> Signed-off-by:
Lu Baolu <baolu.lu@linux.intel.com> Reviewed-by:
Kevin Tian <kevin.tian@intel.com> Reviewed-by:
Joerg Roedel <jroedel@suse.de> Signed-off-by:
-
Yian Chen authored
commit 316f92a7 upstream. Notifier calling chain uses priority to determine the execution order of the notifiers or listeners registered to the chain. PCI bus device hot add utilizes the notification mechanism. The current code sets low priority (INT_MIN) to Intel dmar_pci_bus_notifier and postpones DMAR decoding after adding new device into IOMMU. The result is that struct device pointer cannot be found in DRHD search for the new device's DMAR/IOMMU. Subsequently, the device is put under the "catch-all" IOMMU instead of the correct one. This could cause system hang when device TLB invalidation is sent to the wrong IOMMU. Invalidation timeout error and hard lockup have been observed and data inconsistency/crush may occur as well. This patch fixes the issue by setting a positive priority(1) for dmar_pci_bus_notifier while the priority of IOMMU bus notifier uses the default value(0), therefore DMAR decoding will be in advance of DRHD search for a new device to find the correct IOMMU. Following is a 2-step example that triggers the bug by simulating PCI device hot add behavior in Intel Sapphire Rapids server. echo 1 > /sys/bus/pci/devices/0000:6a:01.0/remove echo 1 > /sys/bus/pci/rescan Fixes: 59ce0515 ("iommu/vt-d: Update DRHD/RMRR/ATSR device scope") Cc: stable@vger.kernel.org # v3.15+ Reported-by:
Zhang, Bernice <bernice.zhang@intel.com> Signed-off-by:
Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by:
Yian Chen <yian.chen@intel.com> Link: https://lore.kernel.org/r/20220521002115.1624069-1-yian.chen@intel.com Signed-off-by:
-
Joerg Roedel authored
commit c51b8f85 upstream. The IOMMU mailing list has moved to iommu@lists.linux.dev and the old list should bounce by now. Remove it from the MAINTAINERS file. Cc: stable@vger.kernel.org Signed-off-by:
-
Srinivas Kandagatla authored
commit 58136d93 upstream. prepare callback can be called multiple times, so unprepare the stream if its already prepared. Without this DSP is not happy to setting the params on a already prepared graph. Fixes: 9b4fe0f1 ("ASoC: qdsp6: audioreach: add q6apm-dai support") Reported-by:
Srinivasa Rao Mandadapu <quic_srivasam@quicinc.com> Signed-off-by:
Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Link: https://lore.kernel.org/r/20220610144818.511797-1-srinivas.kandagatla@linaro.org Signed-off-by:
Mark Brown <broonie@kernel.org> Signed-off-by:
-
Duy Nguyen authored
commit 374e11f1 upstream. On R-Car V3U, this driver should use suitable register offset instead of other SoCs' one. Otherwise, data transmission failed on R-Car V3U. Fixes: 45721c40 ("can: rcar_canfd: Add support for r8a779a0 SoC") Link: https://lore.kernel.org/all/20220704074611.957191-1-yoshihiro.shimoda.uh@renesas.com Reviewed-by:
Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by:
Duy Nguyen <duy.nguyen.rh@renesas.com> Signed-off-by:
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Signed-off-by:
-
Marc Kleine-Budde authored
commit 1c0e78a2 upstream. In mcp251xfd_register_get_dev_id() the device ID register is read with handcrafted SPI transfers. As all registers, this register is in little endian. Further it is not naturally aligned in struct mcp251xfd_map_buf_nocrc::data. However after the transfer the register content is converted from big endian to CPU endianness not taking care of being unaligned. Fix the conversion by converting from little endian to CPU endianness taking the unaligned source into account. Side note: So far the register content is 0x0 on all mcp251xfd compatible chips, and is only used for an informative printk. Link: https://lore.kernel.org/all/20220627092859.809042-1-mkl@pengutronix.de Fixes: 55e5b97f ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN") Reviewed-by:
Rasmus Villemoes <rasmus.villemoes@prevas.dk> Reviewed-by:
Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> Signed-off-by:
-
Marc Kleine-Budde authored
commit 0ff32bfa upstream. The device ID register is 32 bits wide. The driver uses incorrectly the size of a pointer to a u32 to calculate the length of the SPI transfer. This results in a read of 2 registers on 64 bit platforms. This is no problem on the Linux side, as the RX buffer of the SPI transfer is large enough. In the mpc251xfd chip this results in the read of an undocumented register. So far no problems were observed. Fix the length of the SPI transfer to read the device ID register only. Link: https://lore.kernel.org/all/20220616094914.244440-1-mkl@pengutronix.de Fixes: 55e5b97f ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN") Reported-by:
-
Hangbin Liu authored
commit d28b25a6 upstream. Since commit 8fffa0e3 ("selftests/bpf: Normalize XDP section names in selftests") the xdp_dummy.o's section name has changed to xdp. But some tests are still using "section xdp_dummy", which make the tests failed. Fix them by updating to the new section name. Fixes: 8fffa0e3 ("selftests/bpf: Normalize XDP section names in selftests") Signed-off-by:
Hangbin Liu <liuhangbin@gmail.com> Acked-by:
Andrii Nakryiko <andrii@kernel.org> Link: https://lore.kernel.org/r/20220630062228.3453016-1-liuhangbin@gmail.com Signed-off-by:
Jakub Kicinski <kuba@kernel.org> Signed-off-by:
-
Pablo Neira Ayuso authored
commit 7e6bc1f6 upstream. Make sure element data type and length do not mismatch the one specified by the set declaration. Fixes: 7d740264 ("netfilter: nf_tables: variable sized set element keys / data") Reported-by:
Hugues ANGUELKOV <hanguelkov@randorisec.fr> Signed-off-by:
Pablo Neira Ayuso <pablo@netfilter.org> Signed-off-by:
-
Pablo Neira Ayuso authored
commit 9827a0e6 upstream. New elements that reside in the clone are not released in case that the transaction is aborted. [16302.231754] ------------[ cut here ]------------ [16302.231756] WARNING: CPU: 0 PID: 100509 at net/netfilter/nf_tables_api.c:1864 nf_tables_chain_destroy+0x26/0x127 [nf_tables] [...] [16302.231882] CPU: 0 PID: 100509 Comm: nft Tainted: G W 5.19.0-rc3+ #155 [...] [16302.231887] RIP: 0010:nf_tables_chain_destroy+0x26/0x127 [nf_tables] [16302.231899] Code: f3 fe ff ff 41 55 41 54 55 53 48 8b 6f 10 48 89 fb 48 c7 c7 82 96 d9 a0 8b 55 50 48 8b 75 58 e8 de f5 92 e0 83 7d 50 00 74 09 <0f> 0b 5b 5d 41 5c 41 5d c3 4c 8b 65 00 48 8b 7d 08 49 39 fc 74 05 [...] [16302.231917] Call Trace: [16302.231919] <TASK> [16302.231921] __nf_tables_abort.cold+0x23/0x28 [nf_tables] [16302.231934] nf_tables_abort+0x30/0x50 [nf_tables] [16302.231946] nfnetlink_rcv_batch+0x41a/0x840 [nfnetlink] [16302.231952] ? __nla_validate_parse+0x48/0x190 [16302.231959] nfnetlink_rcv+0x110/0x129 [nfnetlink] [16302.231963] netlink_unicast+0x211/0x340 [16302.231969] netlink_sendmsg+0x21e/0x460 Add nft_set_pipapo_match_destroy() helper function to release the elements in the lookup tables. Stefano Brivio says: "We additionally look for elements pointers in the cloned matching data if priv->dirty is set, because that means that cloned data might point to additional elements we did not commit to the working copy yet (such as the abort path case, but perhaps not limited to it)." Fixes: 3c4287f6 ("nf_tables: Add set type for arbitrary concatenation of ranges") Reviewed-by:
Stefano Brivio <sbrivio@redhat.com> Signed-off-by:
-
Michael Walle authored
commit e6fa930f upstream. Instead of counting the child nodes in the device tree, hardcode the number of ports in the driver itself. The counting won't work at all if an ethernet port is marked as disabled, e.g. because it is not connected on the board at all. It turns out that the LAN9662 and LAN9668 use the same switching IP with the same synthesis parameters. The only difference is that the output ports are not connected. Thus, we can just hardcode the number of physical ports to 8. Fixes: db8bcaad ("net: lan966x: add the basic lan966x driver") Signed-off-by:
Michael Walle <michael@walle.cc> Reviewed-by:
Horatiu Vultur <horatiu.vultur@microchip.com> Link: https://lore.kernel.org/r/20220704153654.1167886-1-michael@walle.cc Signed-off-by:
-
Duoming Zhou authored
commit 148ca045 upstream. There are UAF bugs caused by rose_t0timer_expiry(). The root cause is that del_timer() could not stop the timer handler that is running and there is no synchronization. One of the race conditions is shown below: (thread 1) | (thread 2) | rose_device_event | rose_rt_device_down | rose_remove_neigh rose_t0timer_expiry | rose_stop_t0timer(rose_neigh) ... | del_timer(&neigh->t0timer) | kfree(rose_neigh) //[1]FREE neigh->dce_mode //[2]USE | The rose_neigh is deallocated in position [1] and use in position [2]. The crash trace triggered by POC is like below: BUG: KASAN: use-after-free in expire_timers+0x144/0x320 Write of size 8 at addr ffff888009b19658 by task swapper/0/0 ... Call Trace: <IRQ> dump_stack_lvl+0xbf/0xee print_address_description+0x7b/0x440 print_report+0x101/0x230 ? expire_timers+0x144/0x320 kasan_report+0xed/0x120 ? expire_timers+0x144/0x320 expire_timers+0x144/0x320 __run_timers+0x3ff/0x4d0 run_timer_softirq+0x41/0x80 __do_softirq+0x233/0x544 ... This patch changes rose_stop_ftimer() and rose_stop_t0timer() in rose_remove_neigh() to del_timer_sync() in order that the timer handler could be finished before the resources such as rose_neigh and so on are deallocated. As a result, the UAF bugs could be mitigated. Fixes: 1da177e4 ("Linux-2.6.12-rc2") Signed-off-by:
Duoming Zhou <duoming@zju.edu.cn> Link: https://lore.kernel.org/r/20220705125610.77971-1-duoming@zju.edu.cn Signed-off-by:
-
Oliver Neukum authored
commit b55a21b7 upstream. usbnet_write_cmd_async() mixed up which buffers need to be freed in which error case. v2: add Fixes tag v3: fix uninitialized buf pointer Fixes: 877bd862 ("usbnet: introduce usbnet 3 command helpers") Signed-off-by:
Oliver Neukum <oneukum@suse.com> Link: https://lore.kernel.org/r/20220705125351.17309-1-oneukum@suse.com Signed-off-by:
-
Daniel Borkmann authored
commit 3844d153 upstream. Kuee reported a corner case where the tnum becomes constant after the call to __reg_bound_offset(), but the register's bounds are not, that is, its min bounds are still not equal to the register's max bounds. This in turn allows to leak pointers through turning a pointer register as is into an unknown scalar via adjust_ptr_min_max_vals(). Before: func#0 @0 0: R1=ctx(off=0,imm=0,umax=0,var_off=(0x0; 0x0)) R10=fp(off=0,imm=0,umax=0,var_off=(0x0; 0x0)) 0: (b7) r0 = 1 ; R0_w=scalar(imm=1,umin=1,umax=1,var_off=(0x1; 0x0)) 1: (b7) r3 = 0 ; R3_w=scalar(imm=0,umax=0,var_off=(0x0; 0x0)) 2: (87) r3 = -r3 ; R3_w=scalar() 3: (87) r3 = -r3 ; R3_w=scalar() 4: (47) r3 |= 32767 ; R3_w=scalar(smin=-9223372036854743041,umin=32767,var_off=(0x7fff; 0xffffffffffff8000),s32_min=-2147450881) 5: (75) if r3 s>= 0x0 goto pc+1 ; R3_w=scalar(umin=9223372036854808575,var_off=(0x8000000000007fff; 0x7fffffffffff8000),s32_min=-2147450881,u32_min=32767) 6: (95) exit from 5 to 7: R0=scalar(imm=1,umin=1,umax=1,var_off=(0x1; 0x0)) R1=ctx(off=0,imm=0,umax=0,var_off=(0x0; 0x0)) R3=scalar(umin=32767,umax=9223372036854775807,var_off=(0x7fff; 0x7fffffffffff8000),s32_min=-2147450881) R10=fp(off=0,imm=0,umax=0,var_off=(0x0; 0x0)) 7: (d5) if r3 s<= 0x8000 goto pc+1 ; R3=scalar(umin=32769,umax=9223372036854775807,var_off=(0x7fff; 0x7fffffffffff8000),s32_min=-2147450881,u32_min=32767) 8: (95) exit from 7 to 9: R0=scalar(imm=1,umin=1,umax=1,var_off=(0x1; 0x0)) R1=ctx(off=0,imm=0,umax=0,var_off=(0x0; 0x0)) R3=scalar(umin=32767,umax=32768,var_off=(0x7fff; 0x8000)) R10=fp(off=0,imm=0,umax=0,var_off=(0x0; 0x0)) 9: (07) r3 += -32767 ; R3_w=scalar(imm=0,umax=1,var_off=(0x0; 0x0)) <--- [*] 10: (95) exit What can be seen here is that R3=scalar(umin=32767,umax=32768,var_off=(0x7fff; 0x8000)) after the operation R3 += -32767 results in a 'malformed' constant, that is, R3_w=scalar(imm=0,umax=1,var_off=(0x0; 0x0)). Intersecting with var_off has not been done at that point via __update_reg_bounds(), which would have improved the umax to be equal to umin. Refactor the tnum <> min/max bounds information flow into a reg_bounds_sync() helper and use it consistently everywhere. After the fix, bounds have been corrected to R3_w=scalar(imm=0,umax=0,var_off=(0x0; 0x0)) and thus the register is regarded as a 'proper' constant scalar of 0. After: func#0 @0 0: R1=ctx(off=0,imm=0,umax=0,var_off=(0x0; 0x0)) R10=fp(off=0,imm=0,umax=0,var_off=(0x0; 0x0)) 0: (b7) r0 = 1 ; R0_w=scalar(imm=1,umin=1,umax=1,var_off=(0x1; 0x0)) 1: (b7) r3 = 0 ; R3_w=scalar(imm=0,umax=0,var_off=(0x0; 0x0)) 2: (87) r3 = -r3 ; R3_w=scalar() 3: (87) r3 = -r3 ; R3_w=scalar() 4: (47) r3 |= 32767 ; R3_w=scalar(smin=-9223372036854743041,umin=32767,var_off=(0x7fff; 0xffffffffffff8000),s32_min=-2147450881) 5: (75) if r3 s>= 0x0 goto pc+1 ; R3_w=scalar(umin=9223372036854808575,var_off=(0x8000000000007fff; 0x7fffffffffff8000),s32_min=-2147450881,u32_min=32767) 6: (95) exit from 5 to 7: R0=scalar(imm=1,umin=1,umax=1,var_off=(0x1; 0x0)) R1=ctx(off=0,imm=0,umax=0,var_off=(0x0; 0x0)) R3=scalar(umin=32767,umax=9223372036854775807,var_off=(0x7fff; 0x7fffffffffff8000),s32_min=-2147450881) R10=fp(off=0,imm=0,umax=0,var_off=(0x0; 0x0)) 7: (d5) if r3 s<= 0x8000 goto pc+1 ; R3=scalar(umin=32769,umax=9223372036854775807,var_off=(0x7fff; 0x7fffffffffff8000),s32_min=-2147450881,u32_min=32767) 8: (95) exit from 7 to 9: R0=scalar(imm=1,umin=1,umax=1,var_off=(0x1; 0x0)) R1=ctx(off=0,imm=0,umax=0,var_off=(0x0; 0x0)) R3=scalar(umin=32767,umax=32768,var_off=(0x7fff; 0x8000)) R10=fp(off=0,imm=0,umax=0,var_off=(0x0; 0x0)) 9: (07) r3 += -32767 ; R3_w=scalar(imm=0,umax=0,var_off=(0x0; 0x0)) <--- [*] 10: (95) exit Fixes: b03c9f9f ("bpf/verifier: track signed and unsigned min/max values") Reported-by:
Kuee K1r0a <liulin063@gmail.com> Signed-off-by:
Daniel Borkmann <daniel@iogearbox.net> Signed-off-by:
John Fastabend <john.fastabend@gmail.com> Link: https://lore.kernel.org/bpf/20220701124727.11153-2-daniel@iogearbox.net Signed-off-by:
-
Daniel Borkmann authored
commit a12ca627 upstream. Kuee reported a quirk in the jmp32's jeq/jne simulation, namely that the register value does not match expectations for the fall-through path. For example: Before fix: 0: R1=ctx(off=0,imm=0) R10=fp0 0: (b7) r2 = 0 ; R2_w=P0 1: (b7) r6 = 563 ; R6_w=P563 2: (87) r2 = -r2 ; R2_w=Pscalar() 3: (87) r2 = -r2 ; R2_w=Pscalar() 4: (4c) w2 |= w6 ; R2_w=Pscalar(umin=563,umax=4294967295,var_off=(0x233; 0xfffffdcc),s32_min=-2147483085) R6_w=P563 5: (56) if w2 != 0x8 goto pc+1 ; R2_w=P571 <--- [*] 6: (95) exit R0 !read_ok After fix: 0: R1=ctx(off=0,imm=0) R10=fp0 0: (b7) r2 = 0 ; R2_w=P0 1: (b7) r6 = 563 ; R6_w=P563 2: (87) r2 = -r2 ; R2_w=Pscalar() 3: (87) r2 = -r2 ; R2_w=Pscalar() 4: (4c) w2 |= w6 ; R2_w=Pscalar(umin=563,umax=4294967295,var_off=(0x233; 0xfffffdcc),s32_min=-2147483085) R6_w=P563 5: (56) if w2 != 0x8 goto pc+1 ; R2_w=P8 <--- [*] 6: (95) exit R0 !read_ok As can be seen on line 5 for the branch fall-through path in R2 [*] is that given condition w2 != 0x8 is false, verifier should conclude that r2 = 8 as upper 32 bit are known to be zero. However, verifier incorrectly concludes that r2 = 571 which is far off. The problem is it only marks false{true}_reg as known in the switch for JE/NE case, but at the end of the function, it uses {false,true}_{64,32}off to update {false,true}_reg->var_off and they still hold the prior value of {false,true}_reg->var_off before it got marked as known. The subsequent __reg_combine_32_into_64() then propagates this old var_off and derives new bounds. The information between min/max bounds on {false,true}_reg from setting the register to known const combined with the {false,true}_reg->var_off based on the old information then derives wrong register data. Fix it by detangling the BPF_JEQ/BPF_JNE cases and updating relevant {false,true}_{64,32}off tnums along with the register marking to known constant. Fixes: 3f50f132 ("bpf: Verifier, do explicit ALU32 bounds tracking") Reported-by:
-
Marc Kleine-Budde authored
commit d5a972f5 upstream. In commit 169d00a2 ("can: mcp251xfd: add TX IRQ coalescing support") software based TX coalescing was added to the driver. The key idea is to keep the TX complete IRQ disabled for some time after processing it and re-enable later by a hrtimer. When bringing the interface down, this timer has to be stopped. Add the missing hrtimer_cancel() of the tx_irq_time hrtimer to mcp251xfd_stop(). Link: https://lore.kernel.org/all/20220620143942.891811-1-mkl@pengutronix.de Fixes: 169d00a2 ("can: mcp251xfd: add TX IRQ coalescing support") Cc: stable@vger.kernel.org # v5.18 Reviewed-by:
-
Thomas Kopp authored
commit e3d4ee7d upstream. The mcp251xfd compatible chips have an erratum ([1], [2]), where the received CRC doesn't match the calculated CRC. In commit c7eb923c ("can: mcp251xfd: mcp251xfd_regmap_crc_read(): work around broken CRC on TBC register") the following workaround was implementierend. - If a CRC read error on the TBC register is detected and the first byte is 0x00 or 0x80, the most significant bit of the first byte is flipped and the CRC is calculated again. - If the CRC now matches, the _original_ data is passed to the reader. For now we assume transferred data was OK. New investigations and simulations indicate that the CRC send by the device is calculated on correct data, and the data is incorrectly received by the SPI host controller. Use flipped instead of original data and update workaround description in mcp251xfd_regmap_crc_read(). [1] mcp2517fd: DS80000792C: "Incorrect CRC for certain READ_CRC commands" [2] mcp2518fd: DS80000789C: "Incorrect CRC for certain READ_CRC commands" Link: https://lore.kernel.org/all/DM4PR11MB53901D49578FE265B239E55AFB7C9@DM4PR11MB5390.namprd11.prod.outlook.com Fixes: c7eb923c ("can: mcp251xfd: mcp251xfd_regmap_crc_read(): work around broken CRC on TBC register") Cc: stable@vger.kernel.org Signed-off-by:
Thomas Kopp <thomas.kopp@microchip.com> [mkl: split into 2 patches, update patch description and documentation] Signed-off-by:
-
Thomas Kopp authored
commit 406cc9cd upstream. The mcp251xfd compatible chips have an erratum ([1], [2]), where the received CRC doesn't match the calculated CRC. In commit c7eb923c ("can: mcp251xfd: mcp251xfd_regmap_crc_read(): work around broken CRC on TBC register") the following workaround was implementierend. - If a CRC read error on the TBC register is detected and the first byte is 0x00 or 0x80, the most significant bit of the first byte is flipped and the CRC is calculated again. - If the CRC now matches, the _original_ data is passed to the reader. For now we assume transferred data was OK. Measurements on the mcp2517fd show that the workaround is applicable not only of the lowest byte is 0x00 or 0x80, but also if 3 least significant bits are set. Update check on 1st data byte and workaround description accordingly. [1] mcp2517fd: DS80000792C: "Incorrect CRC for certain READ_CRC commands" [2] mcp2518fd: DS80000789C: "Incorrect CRC for certain READ_CRC commands" Link: https://lore.kernel.org/all/DM4PR11MB53901D49578FE265B239E55AFB7C9@DM4PR11MB5390.namprd11.prod.outlook.com Fixes: c7eb923c ("can: mcp251xfd: mcp251xfd_regmap_crc_read(): work around broken CRC on TBC register") Cc: stable@vger.kernel.org Reported-by:
Pavel Modilaynen <pavel.modilaynen@volvocars.com> Signed-off-by:
-
Jimmy Assarsson authored
commit b3b6df2c upstream. Use correct bittiming limits depending on device. For devices based on USBcanII, Leaf M32C or Leaf i.MX28. Fixes: 080f40a6 ("can: kvaser_usb: Add support for Kvaser CAN/USB devices") Fixes: b4f20130 ("can: kvaser_usb: add support for Kvaser Leaf v2 and usb mini PCIe") Fixes: f5d4abea ("can: kvaser_usb: Add support for the USBcan-II family") Link: https://lore.kernel.org/all/20220603083820.800246-4-extja@kvaser.com Cc: stable@vger.kernel.org Signed-off-by:
Jimmy Assarsson <extja@kvaser.com> [mkl: remove stray netlink.h include] [mkl: keep struct can_bittiming_const kvaser_usb_flexc_bittiming_const in kvaser_usb_hydra.c] Signed-off-by:
-
Jimmy Assarsson authored
commit e6c80e60 upstream. The firmware of M32C based Leaf devices expects bittiming parameters calculated for 16MHz clock. Since we use the actual clock frequency of the device, the device may end up with wrong bittiming parameters, depending on user requested parameters. This regression affects M32C based Leaf devices with non-16MHz clock. Fixes: fb12797a ("can: kvaser_usb: get CAN clock frequency from device") Link: https://lore.kernel.org/all/20220603083820.800246-3-extja@kvaser.com Cc: stable@vger.kernel.org Signed-off-by:
-
Jimmy Assarsson authored
commit 49f274c7 upstream. Unify and move compile-time known information into new struct kvaser_usb_driver_info, in favor of run-time checks. All Kvaser USBcanII supports listen-only mode and error counter reporting. Link: https://lore.kernel.org/all/20220603083820.800246-2-extja@kvaser.com Suggested-by:
-
Marc Kleine-Budde authored
commit 4c333369 upstream. In commit 1be37d3b ("can: m_can: fix periph RX path: use rx-offload to ensure skbs are sent from softirq context") the RX path for peripheral devices was switched to RX-offload. Received CAN frames are pushed to RX-offload together with a timestamp. RX-offload is designed to handle overflows of the timestamp correctly, if 32 bit timestamps are provided. The timestamps of m_can core are only 16 bits wide. So this patch shifts them to full 32 bit before passing them to RX-offload. Link: https://lore.kernel.org/all/20220612211410.4081390-1-mkl@pengutronix.de Fixes: 1be37d3b ("can: m_can: fix periph RX path: use rx-offload to ensure skbs are sent from softirq context") Cc: <stable@vger.kernel.org> # 5.13 Cc: Torin Cooper-Bennun <torin@maxiluxsystems.com> Reviewed-by:
Chandrasekar Ramakrishnan <rcsekar@samsung.com> Signed-off-by:
-
Marc Kleine-Budde authored
commit 5b12933d upstream. In commit df06fd67 ("can: m_can: m_can_chip_config(): enable and configure internal timestamps") the timestamping in the m_can core should be enabled. In peripheral mode, the RX'ed CAN frames, TX compete frames and error events are sorted by the timestamp. The above mentioned commit however forgot to enable the timestamping. Add the missing bits to enable the timestamp counter to the write of the Timestamp Counter Configuration register. Link: https://lore.kernel.org/all/20220612212708.4081756-1-mkl@pengutronix.de Fixes: df06fd67 ("can: m_can: m_can_chip_config(): enable and configure internal timestamps") Cc: <stable@vger.kernel.org> # 5.13 Cc: Torin Cooper-Bennun <torin@maxiluxsystems.com> Reviewed-by:
-
Rhett Aultman authored
commit 2bda24ef upstream. The gs_usb driver appears to suffer from a malady common to many USB CAN adapter drivers in that it performs usb_alloc_coherent() to allocate a number of USB request blocks (URBs) for RX, and then later relies on usb_kill_anchored_urbs() to free them, but this doesn't actually free them. As a result, this may be leaking DMA memory that's been used by the driver. This commit is an adaptation of the techniques found in the esd_usb2 driver where a similar design pattern led to a memory leak. It explicitly frees the RX URBs and their DMA memory via a call to usb_free_coherent(). Since the RX URBs were allocated in the gs_can_open(), we remove them in gs_can_close() rather than in the disconnect function as was done in esd_usb2. For more information, see the 928150fa ("can: esd_usb2: fix memory leak"). Link: https://lore.kernel.org/all/alpine.DEB.2.22.394.2206031547001.1630869@thelappy Fixes: d08e973a ("can: gs_usb: Added support for the GS_USB CAN devices") Cc: stable@vger.kernel.org Signed-off-by:
Rhett Aultman <rhett.aultman@samsara.com> Signed-off-by:
-
Liang He authored
commit 562fed94 upstream. In grcan_probe(), of_find_node_by_path() has already increased the refcount. There is no need to call of_node_get() again, so remove it. Link: https://lore.kernel.org/all/20220619070257.4067022-1-windhl@126.com Fixes: 1e93ed26 ("can: grcan: grcan_probe(): fix broken system id check for errata workaround needs") Cc: stable@vger.kernel.org # v5.18 Cc: Andreas Larsson <andreas@gaisler.com> Signed-off-by:
Liang He <windhl@126.com> Signed-off-by:
-
Oliver Hartkopp authored
commit f1b4e32a upstream. In commit d5f9023f ("can: bcm: delay release of struct bcm_op after synchronize_rcu()") Thadeu Lima de Souza Cascardo introduced two synchronize_rcu() calls in bcm_release() (only once at socket close) and in bcm_delete_rx_op() (called on removal of each single bcm_op). Unfortunately this slow removal of the bcm_op's affects user space applications like cansniffer where the modification of a filter removes 2048 bcm_op's which blocks the cansniffer application for 40(!) seconds. In commit 181d4447 ("can: gw: use call_rcu() instead of costly synchronize_rcu()") Eric Dumazet replaced the synchronize_rcu() calls with several call_rcu()'s to safely remove the data structures after the removal of CAN ID subscriptions with can_rx_unregister() calls. This patch adopts Erics approach for the can-bcm which should be applicable since the removal of tasklet_kill() in bcm_remove_op() and the introduction of the HRTIMER_MODE_SOFT timer handling in Linux 5.4. Fixes: d5f9023f ("can: bcm: delay release of struct bcm_op after synchronize_rcu()") # >= 5.4 Link: https://lore.kernel.org/all/20220520183239.19111-1-socketcan@hartkopp.net Cc: stable@vger.kernel.org Cc: Eric Dumazet <edumazet@google.com> Cc: Norbert Slusarek <nslusarek@gmx.net> Cc: Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Signed-off-by:
Oliver Hartkopp <socketcan@hartkopp.net> Signed-off-by:
-
Takashi Iwai authored
commit c5e58c45 upstream. The previous cleanup with devres may lead to the incorrect release orders at the probe error handling due to the devres's nature. Until we register the card, snd_card_free() has to be called at first for releasing the stuff properly when the driver tries to manage and release the stuff via card->private_free(). This patch fixes it by calling snd_card_free() manually on the error from the probe callback. Fixes: 5bff69b3 ("ALSA: cs46xx: Allocate resources with device-managed APIs") Cc: <stable@vger.kernel.org> Reported-and-tested-by:
Jan Engelhardt <jengelh@inai.de> Link: https://lore.kernel.org/r/p2p1s96o-746-74p4-s95-61qo1p7782pn@vanv.qr Link: https://lore.kernel.org/r/20220705152336.350-1-tiwai@suse.de Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Tim Crawford authored
commit 11bea269 upstream. Fixes headset detection on Clevo L140PU. Signed-off-by:
Tim Crawford <tcrawford@system76.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20220624144109.3957-1-tcrawford@system76.com Signed-off-by:
-
Takashi Iwai authored
commit ae8b1631 upstream. Both Behringer UMC 202 HD and 404 HD need explicit quirks to enable the implicit feedback mode and start the playback stream primarily. The former seems fixing the stuttering and the latter is required for a playback-only case. Note that the "clock source 41 is not valid" error message still appears even after this fix, but it should be only once at probe. The reason of the error is still unknown, but this seems to be mostly harmless as it's a one-off error and the driver retires the clock setup and it succeeds afterwards. BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215934 Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20220624101132.14528-1-tiwai@suse.de Signed-off-by:
-
Dylan Yudaken authored
commit 09007af2 upstream. io_import_iovec uses the s pointer, but this was changed immediately after the iovec was re-imported and so it was imported into the wrong place. Change the ordering. Fixes: 2be2eb02 ("io_uring: ensure reads re-import for selected buffers") Signed-off-by:
Dylan Yudaken <dylany@fb.com> Link: https://lore.kernel.org/r/20220630132006.2825668-1-dylany@fb.com [axboe: ensure we don't half-import as well] Signed-off-by:
Jens Axboe <axboe@kernel.dk> Signed-off-by:
-
- 07 Jul, 2022 9 commits
-
-
Greg Kroah-Hartman authored
Link: https://lore.kernel.org/r/20220705115618.410217782@linuxfoundation.org Tested-by: Ronald Warsow <rwarsow@gmx.de Tested-by:
Jon Hunter <jonathanh@nvidia.com> Tested-by:
Justin M. Forbes <jforbes@fedoraproject.org> Tested-by:
Fenil Jain <fkjainco@gmail.com> Tested-by:
Florian Fainelli <f.fainelli@gmail.com> Tested-by:
Ron Economos <re@w6rz.net> Tested-by:
Linux Kernel Functional Testing <lkft@linaro.org> Tested-by:
Rudi Heitbaum <rudi@heitbaum.com> Tested-by:
Sudip Mukherjee <sudip.mukherjee@codethink.co.uk> Tested-by:
Guenter Roeck <linux@roeck-us.net> Tested-by:
Shuah Khan <skhan@linuxfoundation.org> Signed-off-by:
-
Oleksandr Tyshchenko authored
commit b75cd218 upstream. During the PV driver life cycle the mappings are added to the RB-tree by set_foreign_p2m_mapping(), which is called from gnttab_map_refs() and are removed by clear_foreign_p2m_mapping() which is called from gnttab_unmap_refs(). As both functions end up calling __set_phys_to_machine_multi() which updates the RB-tree, this function can be called concurrently. There is already a "p2m_lock" to protect against concurrent accesses, but the problem is that the first read of "phys_to_mach.rb_node" in __set_phys_to_machine_multi() is not covered by it, so this might lead to the incorrect mappings update (removing in our case) in RB-tree. In my environment the related issue happens rarely and only when PV net backend is running, the xen_add_phys_to_mach_entry() claims that it cannot add new pfn <-> mfn mapping to the tree since it is already exists which results in a failure when mapping foreign pages. But there might be other bad consequences related to the non-protected root reads such use-after-free, etc. While at it, also fix the similar usage in __pfn_to_mfn(), so initialize "struct rb_node *n" with the "p2m_lock" held in both functions to avoid possible bad consequences. This is CVE-2022-33744 / XSA-406. Signed-off-by:
Oleksandr Tyshchenko <oleksandr_tyshchenko@epam.com> Reviewed-by:
Stefano Stabellini <sstabellini@kernel.org> Signed-off-by:
Juergen Gross <jgross@suse.com> Signed-off-by:
-
Jan Beulich authored
commit f63c2c20 upstream. The commit referenced below moved the invocation past the "next" label, without any explanation. In fact this allows misbehaving backends undue control over the domain the frontend runs in, as earlier detected errors require the skb to not be freed (it may be retained for later processing via xennet_move_rx_slot(), or it may simply be unsafe to have it freed). This is CVE-2022-33743 / XSA-405. Fixes: 6c5aa6fc ("xen networking: add basic XDP support for xen-netfront") Signed-off-by:
Jan Beulich <jbeulich@suse.com> Reviewed-by:
-
Roger Pau Monne authored
commit 2400617d upstream. Split the current bounce buffering logic used with persistent grants into it's own option, and allow enabling it independently of persistent grants. This allows to reuse the same code paths to perform the bounce buffering required to avoid leaking contiguous data in shared pages not part of the request fragments. Reporting whether the backend is to be trusted can be done using a module parameter, or from the xenstore frontend path as set by the toolstack when adding the device. This is CVE-2022-33742, part of XSA-403. Signed-off-by:
Roger Pau Monné <roger.pau@citrix.com> Reviewed-by:
-
Roger Pau Monne authored
commit 4491001c upstream. Bounce all data on the skbs to be transmitted into zeroed pages if the backend is untrusted. This avoids leaking data present in the pages shared with the backend but not part of the skb fragments. This requires introducing a new helper in order to allocate skbs with a size multiple of XEN_PAGE_SIZE so we don't leak contiguous data on the granted pages. Reporting whether the backend is to be trusted can be done using a module parameter, or from the xenstore frontend path as set by the toolstack when adding the device. This is CVE-2022-33741, part of XSA-403. Signed-off-by:
-
Roger Pau Monne authored
commit 307c8de2 upstream. When allocating pages to be used for shared communication with the backend always zero them, this avoids leaking unintended data present on the pages. This is CVE-2022-33740, part of XSA-403. Signed-off-by:
-
Roger Pau Monne authored
commit 2f446ffe upstream. When allocating pages to be used for shared communication with the backend always zero them, this avoids leaking unintended data present on the pages. This is CVE-2022-26365, part of XSA-403. Signed-off-by:
-
Yang Yingliang authored
[ Upstream commit d0e51022 ] If platform_device_add() fails, it no need to call platform_device_del(), split platform_device_unregister() into platform_device_del/put(), so platform_device_put() can be called separately. Fixes: 8808a793 ("ibmaem: new driver for power/energy/temp meters in IBM System X hardware") Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Yang Yingliang <yangyingliang@huawei.com> Link: https://lore.kernel.org/r/20220701074153.4021556-1-yangyingliang@huawei.com Signed-off-by:
Sasha Levin <sashal@kernel.org>
-
Casper Andersson authored
[ Upstream commit 9c5de246 ] When adding/deleting mdb entries on other net_devices, eg., tap interfaces, it should not crash. Fixes: 3bacfccd ("net: sparx5: Add mdb handlers") Signed-off-by:
Casper Andersson <casper.casan@gmail.com> Reviewed-by:
Steen Hegelund <Steen.Hegelund@microchip.com> Link: https://lore.kernel.org/r/20220630122226.316812-1-casper.casan@gmail.com Signed-off-by:
-
