- 26 Nov, 2022 40 commits
-
-
Yann Gautier authored
commit 39a72dbf upstream. In mmc_select_voltage(), if there is no full power cycle, the voltage range selected at the end of the function will be on a single range (e.g. 3.3V/3.4V). To keep a range around the selected voltage (3.2V/3.4V), the mask shift should be reduced by 1. This issue was triggered by using a specific SD-card (Verbatim Premium 16GB UHS-1) on an STM32MP157C-DK2 board. This board cannot do UHS modes and there is no power cycle. And the card was failing to switch to high-speed mode. When adding the range 3.2V/3.3V for this card with the proposed shift change, the card can switch to high-speed mode. Fixes: ce69d37b ("mmc: core: Prevent violation of specs while initializing cards") Signed-off-by:
Yann Gautier <yann.gautier@foss.st.com> Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20221028073740.7259-1-yann.gautier@foss.st.com Signed-off-by:
Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-
Brian Norris authored
commit 65946690 upstream. The coreboot_table driver registers a coreboot bus while probing a "coreboot_table" device representing the coreboot table memory region. Probing this device (i.e., registering the bus) is a dependency for the module_init() functions of any driver for this bus (e.g., memconsole-coreboot.c / memconsole_driver_init()). With synchronous probe, this dependency works OK, as the link order in the Makefile ensures coreboot_table_driver_init() (and thus, coreboot_table_probe()) completes before a coreboot device driver tries to add itself to the bus. With asynchronous probe, however, coreboot_table_probe() may race with memconsole_driver_init(), and so we're liable to hit one of these two: 1. coreboot_driver_register() eventually hits "[...] the bus was not initialized.", and the memconsole driver fails to register; or 2. coreboot_driver_register() gets past #1, but still races with bus_register() and hits some other undefined/crashing behavior (e.g., in driver_find() [1]) We can resolve this by registering the bus in our initcall, and only deferring "device" work (scanning the coreboot memory region and creating sub-devices) to probe(). [1] Example failure, using 'driver_async_probe=*' kernel command line: [ 0.114217] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000010 ... [ 0.114307] CPU: 1 PID: 1 Comm: swapper/0 Not tainted 6.1.0-rc1 #63 [ 0.114316] Hardware name: Google Scarlet (DT) ... [ 0.114488] Call trace: [ 0.114494] _raw_spin_lock+0x34/0x60 [ 0.114502] kset_find_obj+0x28/0x84 [ 0.114511] driver_find+0x30/0x50 [ 0.114520] driver_register+0x64/0x10c [ 0.114528] coreboot_driver_register+0x30/0x3c [ 0.114540] memconsole_driver_init+0x24/0x30 [ 0.114550] do_one_initcall+0x154/0x2e0 [ 0.114560] do_initcall_level+0x134/0x160 [ 0.114571] do_initcalls+0x60/0xa0 [ 0.114579] do_basic_setup+0x28/0x34 [ 0.114588] kernel_init_freeable+0xf8/0x150 [ 0.114596] kernel_init+0x2c/0x12c [ 0.114607] ret_from_fork+0x10/0x20 [ 0.114624] Code: 5280002b 1100054a b900092a f9800011 (885ffc01) [ 0.114631] ---[ end trace 0000000000000000 ]--- Fixes: b81e3140 ("firmware: coreboot: Make bus registration symmetric") Cc: <stable@vger.kernel.org> Signed-off-by:
Brian Norris <briannorris@chromium.org> Reviewed-by:
Guenter Roeck <linux@roeck-us.net> Reviewed-by:
Stephen Boyd <swboyd@chromium.org> Link: https://lore.kernel.org/r/20221019180934.1.If29e167d8a4771b0bf4a39c89c6946ed764817b9@changeid Signed-off-by:
-
Tina Zhang authored
commit 7fc961cf upstream. SRS cap is the hardware cap telling if the hardware IOMMU can support requests seeking supervisor privilege or not. SRE bit in scalable-mode PASID table entry is treated as Reserved(0) for implementation not supporting SRS cap. Checking SRS cap before setting SRE bit can avoid the non-recoverable fault of "Non-zero reserved field set in PASID Table Entry" caused by setting SRE bit while there is no SRS cap support. The fault messages look like below: DMAR: DRHD: handling fault status reg 2 DMAR: [DMA Read NO_PASID] Request device [00:0d.0] fault addr 0x1154e1000 [fault reason 0x5a] SM: Non-zero reserved field set in PASID Table Entry Fixes: 6f7db75e ("iommu/vt-d: Add second level page table interface") Cc: stable@vger.kernel.org Signed-off-by:
Tina Zhang <tina.zhang@intel.com> Link: https://lore.kernel.org/r/20221115070346.1112273-1-tina.zhang@intel.com Signed-off-by:
Lu Baolu <baolu.lu@linux.intel.com> Link: https://lore.kernel.org/r/20221116051544.26540-3-baolu.lu@linux.intel.com Signed-off-by:
Joerg Roedel <jroedel@suse.de> Signed-off-by:
-
Tina Zhang authored
commit 242b0aae upstream. The A/D bits are preseted for IOVA over first level(FL) usage for both kernel DMA (i.e, domain typs is IOMMU_DOMAIN_DMA) and user space DMA usage (i.e., domain type is IOMMU_DOMAIN_UNMANAGED). Presetting A bit in FL requires to preset the bit in every related paging entries, including the non-leaf ones. Otherwise, hardware may treat this as an error. For example, in a case of ECAP_REG.SMPWC==0, DMA faults might occur with below DMAR fault messages (wrapped for line length) dumped. DMAR: DRHD: handling fault status reg 2 DMAR: [DMA Read NO_PASID] Request device [aa:00.0] fault addr 0x10c3a6000 [fault reason 0x90] SM: A/D bit update needed in first-level entry when set up in no snoop Fixes: 289b3b00 ("iommu/vt-d: Preset A/D bits for user space DMA usage") Cc: stable@vger.kernel.org Signed-off-by:
-
Benjamin Block authored
commit 0954256e upstream. We used to use the wrong type of integer in 'zfcp_fsf_req_send()' to cache the FSF request ID when sending a new FSF request. This is used in case the sending fails and we need to remove the request from our internal hash table again (so we don't keep an invalid reference and use it when we free the request again). In 'zfcp_fsf_req_send()' we used to cache the ID as 'int' (signed and 32 bit wide), but the rest of the zfcp code (and the firmware specification) handles the ID as 'unsigned long'/'u64' (unsigned and 64 bit wide [s390x ELF ABI]). For one this has the obvious problem that when the ID grows past 32 bit (this can happen reasonably fast) it is truncated to 32 bit when storing it in the cache variable and so doesn't match the original ID anymore. The second less obvious problem is that even when the original ID has not yet grown past 32 bit, as soon as the 32nd bit is set in the original ID (0x80000000 = 2'147'483'648) we will have a mismatch when we cast it back to 'unsigned long'. As the cached variable is of a signed type, the compiler will choose a sign-extending instruction to load the 32 bit variable into a 64 bit register (e.g.: 'lgf %r11,188(%r15)'). So once we pass the cached variable into 'zfcp_reqlist_find_rm()' to remove the request again all the leading zeros will be flipped to ones to extend the sign and won't match the original ID anymore (this has been observed in practice). If we can't successfully remove the request from the hash table again after 'zfcp_qdio_send()' fails (this happens regularly when zfcp cannot notify the adapter about new work because the adapter is already gone during e.g. a ChpID toggle) we will end up with a double free. We unconditionally free the request in the calling function when 'zfcp_fsf_req_send()' fails, but because the request is still in the hash table we end up with a stale memory reference, and once the zfcp adapter is either reset during recovery or shutdown we end up freeing the same memory twice. The resulting stack traces vary depending on the kernel and have no direct correlation to the place where the bug occurs. Here are three examples that have been seen in practice: list_del corruption. next->prev should be 00000001b9d13800, but was 00000000dead4ead. (next=00000001bd131a00) ------------[ cut here ]------------ kernel BUG at lib/list_debug.c:62! monitor event: 0040 ilc:2 [#1] PREEMPT SMP Modules linked in: ... CPU: 9 PID: 1617 Comm: zfcperp0.0.1740 Kdump: loaded Hardware name: ... Krnl PSW : 0704d00180000000 00000003cbeea1f8 (__list_del_entry_valid+0x98/0x140) R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:1 PM:0 RI:0 EA:3 Krnl GPRS: 00000000916d12f1 0000000080000000 000000000000006d 00000003cb665cd6 0000000000000001 0000000000000000 0000000000000000 00000000d28d21e8 00000000d3844000 00000380099efd28 00000001bd131a00 00000001b9d13800 00000000d3290100 0000000000000000 00000003cbeea1f4 00000380099efc70 Krnl Code: 00000003cbeea1e8: c020004f68a7 larl %r2,00000003cc8d7336 00000003cbeea1ee: c0e50027fd65 brasl %r14,00000003cc3e9cb8 #00000003cbeea1f4: af000000 mc 0,0 >00000003cbeea1f8: c02000920440 larl %r2,00000003cd12aa78 00000003cbeea1fe: c0e500289c25 brasl %r14,00000003cc3fda48 00000003cbeea204: b9040043 lgr %r4,%r3 00000003cbeea208: b9040051 lgr %r5,%r1 00000003cbeea20c: b9040032 lgr %r3,%r2 Call Trace: [<00000003cbeea1f8>] __list_del_entry_valid+0x98/0x140 ([<00000003cbeea1f4>] __list_del_entry_valid+0x94/0x140) [<000003ff7ff502fe>] zfcp_fsf_req_dismiss_all+0xde/0x150 [zfcp] [<000003ff7ff49cd0>] zfcp_erp_strategy_do_action+0x160/0x280 [zfcp] [<000003ff7ff4a22e>] zfcp_erp_strategy+0x21e/0xca0 [zfcp] [<000003ff7ff4ad34>] zfcp_erp_thread+0x84/0x1a0 [zfcp] [<00000003cb5eece8>] kthread+0x138/0x150 [<00000003cb557f3c>] __ret_from_fork+0x3c/0x60 [<00000003cc4172ea>] ret_from_fork+0xa/0x40 INFO: lockdep is turned off. Last Breaking-Event-Address: [<00000003cc3e9d04>] _printk+0x4c/0x58 Kernel panic - not syncing: Fatal exception: panic_on_oops or: Unable to handle kernel pointer dereference in virtual kernel address space Failing address: 6b6b6b6b6b6b6000 TEID: 6b6b6b6b6b6b6803 Fault in home space mode while using kernel ASCE. AS:0000000063b10007 R3:0000000000000024 Oops: 0038 ilc:3 [#1] SMP Modules linked in: ... CPU: 10 PID: 0 Comm: swapper/10 Kdump: loaded Hardware name: ... Krnl PSW : 0404d00180000000 000003ff7febaf8e (zfcp_fsf_reqid_check+0x86/0x158 [zfcp]) R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:3 CC:1 PM:0 RI:0 EA:3 Krnl GPRS: 5a6f1cfa89c49ac3 00000000aff2c4c8 6b6b6b6b6b6b6b6b 00000000000002a8 0000000000000000 0000000000000055 0000000000000000 00000000a8515800 0700000000000000 00000000a6e14500 00000000aff2c000 000000008003c44c 000000008093c700 0000000000000010 00000380009ebba8 00000380009ebb48 Krnl Code: 000003ff7febaf7e: a7f4003d brc 15,000003ff7febaff8 000003ff7febaf82: e32020000004 lg %r2,0(%r2) #000003ff7febaf88: ec2100388064 cgrj %r2,%r1,8,000003ff7febaff8 >000003ff7febaf8e: e3b020100020 cg %r11,16(%r2) 000003ff7febaf94: a774fff7 brc 7,000003ff7febaf82 000003ff7febaf98: ec280030007c cgij %r2,0,8,000003ff7febaff8 000003ff7febaf9e: e31020080004 lg %r1,8(%r2) 000003ff7febafa4: e33020000004 lg %r3,0(%r2) Call Trace: [<000003ff7febaf8e>] zfcp_fsf_reqid_check+0x86/0x158 [zfcp] [<000003ff7febbdbc>] zfcp_qdio_int_resp+0x6c/0x170 [zfcp] [<000003ff7febbf90>] zfcp_qdio_irq_tasklet+0xd0/0x108 [zfcp] [<0000000061d90a04>] tasklet_action_common.constprop.0+0xdc/0x128 [<000000006292f300>] __do_softirq+0x130/0x3c0 [<0000000061d906c6>] irq_exit_rcu+0xfe/0x118 [<000000006291e818>] do_io_irq+0xc8/0x168 [<000000006292d516>] io_int_handler+0xd6/0x110 [<000000006292d596>] psw_idle_exit+0x0/0xa ([<0000000061d3be50>] arch_cpu_idle+0x40/0xd0) [<000000006292ceea>] default_idle_call+0x52/0xf8 [<0000000061de4fa4>] do_idle+0xd4/0x168 [<0000000061de51fe>] cpu_startup_entry+0x36/0x40 [<0000000061d4faac>] smp_start_secondary+0x12c/0x138 [<000000006292d88e>] restart_int_handler+0x6e/0x90 Last Breaking-Event-Address: [<000003ff7febaf94>] zfcp_fsf_reqid_check+0x8c/0x158 [zfcp] Kernel panic - not syncing: Fatal exception in interrupt or: Unable to handle kernel pointer dereference in virtual kernel address space Failing address: 523b05d3ae76a000 TEID: 523b05d3ae76a803 Fault in home space mode while using kernel ASCE. AS:0000000077c40007 R3:0000000000000024 Oops: 0038 ilc:3 [#1] SMP Modules linked in: ... CPU: 3 PID: 453 Comm: kworker/3:1H Kdump: loaded Hardware name: ... Workqueue: kblockd blk_mq_run_work_fn Krnl PSW : 0404d00180000000 0000000076fc0312 (__kmalloc+0xd2/0x398) R:0 T:1 IO:0 EX:0 Key:0 M:1 W:0 P:0 AS:3 CC:1 PM:0 RI:0 EA:3 Krnl GPRS: ffffffffffffffff 523b05d3ae76abf6 0000000000000000 0000000000092a20 0000000000000002 00000007e49b5cc0 00000007eda8f000 0000000000092a20 00000007eda8f000 00000003b02856b9 00000000000000a8 523b05d3ae76abf6 00000007dd662000 00000007eda8f000 0000000076fc02b2 000003e0037637a0 Krnl Code: 0000000076fc0302: c004000000d4 brcl 0,76fc04aa 0000000076fc0308: b904001b lgr %r1,%r11 #0000000076fc030c: e3106020001a algf %r1,32(%r6) >0000000076fc0312: e31010000082 xg %r1,0(%r1) 0000000076fc0318: b9040001 lgr %r0,%r1 0000000076fc031c: e30061700082 xg %r0,368(%r6) 0000000076fc0322: ec59000100d9 aghik %r5,%r9,1 0000000076fc0328: e34003b80004 lg %r4,952 Call Trace: [<0000000076fc0312>] __kmalloc+0xd2/0x398 [<0000000076f318f2>] mempool_alloc+0x72/0x1f8 [<000003ff8027c5f8>] zfcp_fsf_req_create.isra.7+0x40/0x268 [zfcp] [<000003ff8027f1bc>] zfcp_fsf_fcp_cmnd+0xac/0x3f0 [zfcp] [<000003ff80280f1a>] zfcp_scsi_queuecommand+0x122/0x1d0 [zfcp] [<000003ff800b4218>] scsi_queue_rq+0x778/0xa10 [scsi_mod] [<00000000771782a0>] __blk_mq_try_issue_directly+0x130/0x208 [<000000007717a124>] blk_mq_request_issue_directly+0x4c/0xa8 [<000003ff801302e2>] dm_mq_queue_rq+0x2ea/0x468 [dm_mod] [<0000000077178c12>] blk_mq_dispatch_rq_list+0x33a/0x818 [<000000007717f064>] __blk_mq_do_dispatch_sched+0x284/0x2f0 [<000000007717f44c>] __blk_mq_sched_dispatch_requests+0x1c4/0x218 [<000000007717fa7a>] blk_mq_sched_dispatch_requests+0x52/0x90 [<0000000077176d74>] __blk_mq_run_hw_queue+0x9c/0xc0 [<0000000076da6d74>] process_one_work+0x274/0x4d0 [<0000000076da7018>] worker_thread+0x48/0x560 [<0000000076daef18>] kthread+0x140/0x160 [<000000007751d144>] ret_from_fork+0x28/0x30 Last Breaking-Event-Address: [<0000000076fc0474>] __kmalloc+0x234/0x398 Kernel panic - not syncing: Fatal exception: panic_on_oops To fix this, simply change the type of the cache variable to 'unsigned long', like the rest of zfcp and also the argument for 'zfcp_reqlist_find_rm()'. This prevents truncation and wrong sign extension and so can successfully remove the request from the hash table. Fixes: e60a6d69 ("[SCSI] zfcp: Remove function zfcp_reqlist_find_safe") Cc: <stable@vger.kernel.org> #v2.6.34+ Signed-off-by:
Benjamin Block <bblock@linux.ibm.com> Link: https://lore.kernel.org/r/979f6e6019d15f91ba56182f1aaf68d61bf37fc6.1668595505.git.bblock@linux.ibm.com Reviewed-by:
Steffen Maier <maier@linux.ibm.com> Signed-off-by:
Martin K. Petersen <martin.petersen@oracle.com> Signed-off-by:
-
Aminuddin Jamaluddin authored
commit 18c532e4 upstream. Sleep time is added to ensure the phy to be ready after loopback bit was set. This to prevent the phy loopback test from failing. Fixes: 020a45af ("net: phy: marvell: add Marvell specific PHY loopback") Cc: <stable@vger.kernel.org> # 5.15.x Signed-off-by:
Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com> Signed-off-by:
Aminuddin Jamaluddin <aminuddin.jamaluddin@intel.com> Link: https://lore.kernel.org/r/20221114065302.10625-1-aminuddin.jamaluddin@intel.com Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Signed-off-by:
-
Alban Crequy authored
commit 8678ea06 upstream. If a page fault occurs while copying the first byte, this function resets one byte before dst. As a consequence, an address could be modified and leaded to kernel crashes if case the modified address was accessed later. Fixes: b58294ea ("maccess: allow architectures to provide kernel probing directly") Signed-off-by:
Alban Crequy <albancrequy@linux.microsoft.com> Signed-off-by:
Andrii Nakryiko <andrii@kernel.org> Tested-by:
Francis Laniel <flaniel@linux.microsoft.com> Reviewed-by:
Andrew Morton <akpm@linux-foundation.org> Cc: <stable@vger.kernel.org> [5.8] Link: https://lore.kernel.org/bpf/20221110085614.111213-2-albancrequy@linux.microsoft.com Signed-off-by:
-
Tetsuo Handa authored
commit b8ebf250 upstream. syzbot is reporting uninitialized value at iforce_init_device() [1], for commit 6ac0aec6 ("Input: iforce - allow callers supply data buffer when fetching device IDs") is checking that valid length is shorter than bytes to read. Since iforce_get_id_packet() stores valid length when returning 0, the caller needs to check that valid length is longer than or equals to bytes to read. Reported-by:
syzbot <syzbot+4dd880c1184280378821@syzkaller.appspotmail.com> Signed-off-by:
Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Fixes: 6ac0aec6 ("Input: iforce - allow callers supply data buffer when fetching device IDs") Link: https://lore.kernel.org/r/531fb432-7396-ad37-ecba-3e42e7f56d5c@I-love.SAKURA.ne.jp Cc: stable@vger.kernel.org Signed-off-by:
Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by:
-
Ilpo Järvinen authored
commit 1bfcbe58 upstream. If the platform doesn't use DMA device filter (as is the case with Elkhart Lake), whole lpss8250_dma_setup() setup is skipped. This results in skipping also *_maxburst setup which is undesirable. Refactor lpss8250_dma_setup() to configure DMA even if filter is not setup. Cc: stable <stable@kernel.org> Signed-off-by:
Ilpo Järvinen <ilpo.jarvinen@linux.intel.com> Reviewed-by:
Andy Shevchenko <andriy.shevchenko@linux.intel.com> Link: https://lore.kernel.org/r/20221108121952.5497-3-ilpo.jarvinen@linux.intel.com Signed-off-by:
-
Ilpo Järvinen authored
commit 1980860e upstream. Returning true from handle_rx_dma() without flushing DMA first creates a data ordering hazard. If DMA Rx has handled any character at the point when RLSI occurs, the non-DMA path handles any pending characters jumping them ahead of those characters that are pending under DMA. Fixes: 75df022b ("serial: 8250_dma: Fix RX handling") Cc: <stable@vger.kernel.org> Signed-off-by:
-
Ilpo Järvinen authored
commit a931237c upstream. DW UART sometimes triggers IIR_RDI during DMA Rx when IIR_RX_TIMEOUT should have been triggered instead. Since IIR_RDI has higher priority than IIR_RX_TIMEOUT, this causes the Rx to hang into interrupt loop. The problem seems to occur at least with some combinations of small-sized transfers (I've reproduced the problem on Elkhart Lake PSE UARTs). If there's already an on-going Rx DMA and IIR_RDI triggers, fall graciously back to non-DMA Rx. That is, behave as if IIR_RX_TIMEOUT had occurred. 8250_omap already considers IIR_RDI similar to this change so its nothing unheard of. Fixes: 75df022b ("serial: 8250_dma: Fix RX handling") Cc: <stable@vger.kernel.org> Co-developed-by:
Srikanth Thokala <srikanth.thokala@intel.com> Signed-off-by:
Aman Kumar <aman.kumar@intel.com> Signed-off-by:
-
Mikulas Patocka authored
commit 4fe1ec99 upstream. __list_versions will first estimate the required space using the "dm_target_iterate(list_version_get_needed, &needed)" call and then will fill the space using the "dm_target_iterate(list_version_get_info, &iter_info)" call. Each of these calls locks the targets using the "down_read(&_lock)" and "up_read(&_lock)" calls, however between the first and second "dm_target_iterate" there is no lock held and the target modules can be loaded at this point, so the second "dm_target_iterate" call may need more space than what was the first "dm_target_iterate" returned. The code tries to handle this overflow (see the beginning of list_version_get_info), however this handling is incorrect. The code sets "param->data_size = param->data_start + needed" and "iter_info.end = (char *)vers+len" - "needed" is the size returned by the first dm_target_iterate call; "len" is the size of the buffer allocated by userspace. "len" may be greater than "needed"; in this case, the code will write up to "len" bytes into the buffer, however param->data_size is set to "needed", so it may write data past the param->data_size value. The ioctl interface copies only up to param->data_size into userspace, thus part of the result will be truncated. Fix this bug by setting "iter_info.end = (char *)vers + needed;" - this guarantees that the second "dm_target_iterate" call will write only up to the "needed" buffer and it will exit with "DM_BUFFER_FULL_FLAG" if it overflows the "needed" space - in this case, userspace will allocate a larger buffer and retry. Note that there is also a bug in list_version_get_needed - we need to add "strlen(tt->name) + 1" to the needed size, not "strlen(tt->name)". Cc: stable@vger.kernel.org Signed-off-by:
Mikulas Patocka <mpatocka@redhat.com> Signed-off-by:
Mike Snitzer <snitzer@kernel.org> Signed-off-by:
-
Mitja Spes authored
commit 741cec30 upstream. Don't hardcode the ms5611 SPI speed, limit it instead. Signed-off-by:
Mitja Spes <mitja@lxnav.com> Fixes: c0644160 ("iio: pressure: add support for MS5611 pressure and temperature sensor") Link: https://lore.kernel.org/r/20221021135827.1444793-3-mitja@lxnav.com Cc: <Stable@vger.kernel.org> Signed-off-by:
Jonathan Cameron <Jonathan.Cameron@huawei.com> Signed-off-by:
-
Saravanan Sekar authored
commit ca1547ab upstream. Add sentinel at end of maps to avoid potential array out of bound access in iio core. Fixes: 7abd9fb6 ("iio: adc: mp2629: Add support for mp2629 ADC driver") Signed-off-by:
Saravanan Sekar <sravanhome@gmail.com> Link: https://lore.kernel.org/r/20221029093000.45451-4-sravanhome@gmail.com Cc: <Stable@vger.kernel.org> Signed-off-by:
-
Saravanan Sekar authored
commit 1eb20332 upstream. Input voltage channel enum is compared against iio address instead of the channel. Fixes: 7abd9fb6 ("iio: adc: mp2629: Add support for mp2629 ADC driver") Signed-off-by:
Andy Shevchenko <andy.shevchenko@gmail.com> Link: https://lore.kernel.org/r/20221029093000.45451-2-sravanhome@gmail.com Cc: <Stable@vger.kernel.org> Signed-off-by:
-
Yang Yingliang authored
commit efa17e90 upstream. dev_set_name() allocates memory for name, it need be freed when device_add() fails, call put_device() to give up the reference that hold in device_initialize(), so that it can be freed in kobject_cleanup() when the refcount hit to 0. Fault injection test can trigger this: unreferenced object 0xffff8e8340a7b4c0 (size 32): comm "modprobe", pid 243, jiffies 4294678145 (age 48.845s) hex dump (first 32 bytes): 69 69 6f 5f 73 79 73 66 73 5f 74 72 69 67 67 65 iio_sysfs_trigge 72 00 a7 40 83 8e ff ff 00 86 13 c4 f6 ee ff ff r..@............ backtrace: [<0000000074999de8>] __kmem_cache_alloc_node+0x1e9/0x360 [<00000000497fd30b>] __kmalloc_node_track_caller+0x44/0x1a0 [<000000003636c520>] kstrdup+0x2d/0x60 [<0000000032f84da2>] kobject_set_name_vargs+0x1e/0x90 [<0000000092efe493>] dev_set_name+0x4e/0x70 Fixes: 1f785681 ("staging:iio:trigger sysfs userspace trigger rework.") Signed-off-by:
Yang Yingliang <yangyingliang@huawei.com> Cc: <Stable@vger.kernel.org> Link: https://lore.kernel.org/r/20221022074212.1386424-1-yangyingliang@huawei.com Signed-off-by:
-
Yang Yingliang authored
commit 65f20301 upstream. If iio_trigger_register() returns error, it should call iio_trigger_free() to give up the reference that hold in iio_trigger_alloc(), so that it can call iio_trig_release() to free memory when the refcount hit to 0. Fixes: 0e589d5f ("ARM: AT91: IIO: Add AT91 ADC driver.") Signed-off-by:
-
Rajat Khandelwal authored
commit 40bf8f16 upstream. There is no point to enter safe mode during DP/TBT configuration if the DP/TBT was already configured in mux. This is because safe mode is only applicable when there is a need to reconfigure the pins in order to avoid damage within/to port partner. In some chrome systems, IOM/mux is already configured before OS comes up. Thus, when driver is probed, it blindly enters safe mode due to PD negotiations but only after gfx driver lowers dp_phy_ownership, will the IOM complete safe mode and send an ack to PMC. Since, that never happens, we see IPC timeout. Hence, allow safe mode only when pin reconfiguration is not required, which makes sense. Fixes: 43d596e3 ("usb: typec: intel_pmc_mux: Check the port status before connect") Cc: stable <stable@kernel.org> Signed-off-by:
Rajat Khandelwal <rajat.khandelwal@linux.intel.com> Signed-off-by:
Lee Shawn C <shawn.c.lee@intel.com> Reviewed-by:
Heikki Krogerus <heikki.krogerus@linux.intel.com> Link: https://lore.kernel.org/r/20221024171611.181468-1-rajat.khandelwal@linux.intel.com Signed-off-by:
-
Li Jun authored
commit 9d5333c9 upstream. When usb 3.0 hub connect with one USB 2.0 device and NO USB 3.0 device, some usb hub reports endless port reset message. [ 190.324169] usb 2-1: new SuperSpeed USB device number 88 using xhci-hcd [ 190.352834] hub 2-1:1.0: USB hub found [ 190.356995] hub 2-1:1.0: 4 ports detected [ 190.700056] usb 2-1: USB disconnect, device number 88 [ 192.472139] usb 2-1: new SuperSpeed USB device number 89 using xhci-hcd [ 192.500820] hub 2-1:1.0: USB hub found [ 192.504977] hub 2-1:1.0: 4 ports detected [ 192.852066] usb 2-1: USB disconnect, device number 89 The reason is the runtime pm state of USB2.0 port is active and USB 3.0 port is suspend, so parent device is active state. cat /sys/bus/platform/devices/5b110000.usb/5b130000.usb/xhci-hcd.1.auto/usb2/power/runtime_status suspended cat /sys/bus/platform/devices/5b110000.usb/5b130000.usb/xhci-hcd.1.auto/usb1/power/runtime_status active cat /sys/bus/platform/devices/5b110000.usb/5b130000.usb/xhci-hcd.1.auto/power/runtime_status active cat /sys/bus/platform/devices/5b110000.usb/5b130000.usb/power/runtime_status active So xhci_cdns3_suspend_quirk() have not called. U3 configure is not applied. move U3 configure into host start. Reinit again in resume function in case controller power lost during suspend. Cc: stable@vger.kernel.org 5.10 Signed-off-by:
Li Jun <jun.li@nxp.com> Signed-off-by:
Frank Li <Frank.Li@nxp.com> Reviewed-by:
Peter Chen <peter.chen@kernel.org> Acked-by:
Alexander Stein <alexander.stein@ew.tq-group.com> Link: https://lore.kernel.org/r/20221026190749.2280367-1-Frank.Li@nxp.com Signed-off-by:
-
Duoming Zhou authored
commit 7a58b8d6 upstream. There is a deadlock in ci_otg_del_timer(), the process is shown below: (thread 1) | (thread 2) ci_otg_del_timer() | ci_otg_hrtimer_func() ... | spin_lock_irqsave() //(1) | ... ... | hrtimer_cancel() | spin_lock_irqsave() //(2) (block forever) We hold ci->lock in position (1) and use hrtimer_cancel() to wait ci_otg_hrtimer_func() to stop, but ci_otg_hrtimer_func() also need ci->lock in position (2). As a result, the hrtimer_cancel() in ci_otg_del_timer() will be blocked forever. This patch extracts hrtimer_cancel() from the protection of spin_lock_irqsave() in order that the ci_otg_hrtimer_func() could obtain the ci->lock. What`s more, there will be no race happen. Because the "next_timer" is always under the protection of spin_lock_irqsave() and we only check whether "next_timer" equals to NUM_OTG_FSM_TIMERS in the following code. Fixes: 3a316ec4 ("usb: chipidea: use hrtimer for otg fsm timers") Cc: stable <stable@kernel.org> Signed-off-by:
Duoming Zhou <duoming@zju.edu.cn> Link: https://lore.kernel.org/r/20220918033312.94348-1-duoming@zju.edu.cn Signed-off-by:
-
Nicolas Dumazet authored
commit 181135bb upstream. Before adding this quirk, this (mechanical keyboard) device would not be recognized, logging: new full-speed USB device number 56 using xhci_hcd unable to read config index 0 descriptor/start: -32 chopping to 0 config(s) It would take dozens of plugging/unpuggling cycles for the keyboard to be recognized. Keyboard seems to simply work after applying this quirk. This issue had been reported by users in two places already ([1], [2]) but nobody tried upstreaming a patch yet. After testing I believe their suggested fix (DELAY_INIT + NO_LPM + DEVICE_QUALIFIER) was probably a little overkill. I assume this particular combination was tested because it had been previously suggested in [3], but only NO_LPM seems sufficient for this device. [1]: https://qiita.com/float168/items/fed43d540c8e2201b543 [2]: https://blog.kostic.dev/posts/making-the-realforce-87ub-work-with-usb30-on-Ubuntu/ [3]: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1678477 Cc: stable@vger.kernel.org Signed-off-by:
Nicolas Dumazet <ndumazet@google.com> Link: https://lore.kernel.org/r/20221109122946.706036-1-ndumazet@google.com Signed-off-by:
-
Reinhard Speyerer authored
commit 148f4b32 upstream. Add support for the following Fibocom FM160 composition: 0x0111: MBIM + MODEM + DIAG + AT T: Bus=01 Lev=02 Prnt=125 Port=01 Cnt=02 Dev#= 93 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=2cb7 ProdID=0111 Rev= 5.04 S: Manufacturer=Fibocom S: Product=Fibocom FM160 Modem_SN:12345678 S: SerialNumber=12345678 C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00 I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=32ms I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim E: Ad=8e(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=0f(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=option E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=40 Driver=option E: Ad=86(I) Atr=03(Int.) MxPS= 10 Ivl=32ms E: Ad=85(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms Signed-off-by:
Reinhard Speyerer <rspmn@arcor.de> Cc: stable@vger.kernel.org Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Davide Tronchin authored
commit c1547f12 upstream. Add LARA-L6 PIDs for three different USB compositions. LARA-L6 module can be configured (by AT interface) in three different USB modes: * Default mode (Vendor ID: 0x1546 Product ID: 0x1341) with 4 serial interfaces * RmNet mode (Vendor ID: 0x1546 Product ID: 0x1342) with 4 serial interfaces and 1 RmNet virtual network interface * CDC-ECM mode (Vendor ID: 0x1546 Product ID: 0x1343) with 4 serial interface and 1 CDC-ECM virtual network interface In default mode LARA-L6 exposes the following interfaces: If 0: Diagnostic If 1: AT parser If 2: AT parser If 3: AT parser/alternative functions In RmNet mode LARA-L6 exposes the following interfaces: If 0: Diagnostic If 1: AT parser If 2: AT parser If 3: AT parset/alternative functions If 4: RMNET interface In CDC-ECM mode LARA-L6 exposes the following interfaces: If 0: Diagnostic If 1: AT parser If 2: AT parser If 3: AT parset/alternative functions If 4: CDC-ECM interface Signed-off-by:
Davide Tronchin <davide.tronchin.94@gmail.com> [ johan: drop PID defines in favour of comments ] Cc: stable@vger.kernel.org Signed-off-by:
-
Davide Tronchin authored
commit d9e37a5c upstream. The official LARA-R6 (00B) modem uses 0x908b PID. LARA-R6 00B does not implement a QMI interface on port 4, the reservation (RSVD(4)) has been added to meet other companies that implement QMI on that interface. LARA-R6 00B USB composition exposes the following interfaces: If 0: Diagnostic If 1: AT parser If 2: AT parser If 3: AT parser/alternative functions Signed-off-by:
-
Davide Tronchin authored
commit 2ec106b9 upstream. Remove the UBLOX_PRODUCT_R6XX 0x90fa association since LARA-R6 00B final product uses a new USB composition with different PID. 0x90fa PID used only by LARA-R6 internal prototypes. Move 0x90fa PID directly in the option_ids array since used by other Qualcomm based modem vendors as pointed out in: https://lore.kernel.org/all/6572c4e6-d8bc-b8d3-4396-d879e4e76338@gmail.com Signed-off-by:
-
Benoît Monin authored
commit df3414b0 upstream. Add support for the AT and diag ports, similar to other qualcomm SDX55 modems. In QDL mode, the modem uses a different device ID and support is provided by qcserial in commit 11c52d25 ("USB: serial: qcserial: add EM9191 QDL support"). T: Bus=08 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 3 Spd=5000 MxCh= 0 D: Ver= 3.20 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 9 #Cfgs= 1 P: Vendor=1199 ProdID=90d3 Rev=00.06 S: Manufacturer=Sierra Wireless, Incorporated S: Product=Sierra Wireless EM9191 S: SerialNumber=xxxxxxxxxxxxxxxx C: #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=896mA I: If#=0x0 Alt= 0 #EPs= 1 Cls=02(commc) Sub=0e Prot=00 Driver=cdc_mbim I: If#=0x1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none) I: If#=0x4 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=30 Driver=(none) Signed-off-by:
Benoît Monin <benoit.monin@gmx.fr> Cc: stable@vger.kernel.org Signed-off-by:
-
Linus Walleij authored
commit cd136706 upstream. What the code does is to not check the return value from devm_gpiod_get() and then avoid using an erroneous GPIO descriptor with IS_ERR_OR_NULL(). This will miss real errors from the GPIO core that should not be ignored, such as probe deferral. Instead request the GPIO as explicitly optional, which means that if it doesn't exist, the descriptor returned will be NULL. Then we can add error handling and also avoid just doing this on the device tree path, and simplify the site where the optional GPIO descriptor is used. There were some problems with cleaning up this GPIO descriptor use in the past, but this is the proper way to deal with it. Cc: Rafał Miłecki <rafal@milecki.pl> Cc: Chuhong Yuan <hslester96@gmail.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Cc: stable <stable@kernel.org> Link: https://lore.kernel.org/r/20221107090753.1404679-1-linus.walleij@linaro.org Signed-off-by:
-
Mushahid Hussain authored
commit 0fc801f8 upstream. This patch fixes a segfault by adding a null check on synth in speakup_con_update(). The segfault can be reproduced as follows: - Login into a text console - Load speakup and speakup_soft modules - Remove speakup_soft - Switch to a graphics console This is caused by lack of a null check on `synth` in speakup_con_update(). Here's the sequence that causes the segfault: - When we remove the speakup_soft, synth_release() sets the synth to null. - After that, when we change the virtual console to graphics console, vt_notifier_call() is fired, which then calls speakup_con_update(). - Inside speakup_con_update() there's no null check on synth, so it calls synth_printf(). - Inside synth_printf(), synth_buffer_add() and synth_start(), both access synth, when it is null and causing a segfault. Therefore adding a null check on synth solves the issue. Fixes: 2610df41 ("staging: speakup: Add pause command used on switching to graphical mode") Cc: stable <stable@kernel.org> Signed-off-by:
Mushahid Hussain <mushi.shar@gmail.com> Signed-off-by:
Samuel Thibault <samuel.thibault@ens-lyon.org> Link: https://lore.kernel.org/r/20221010165720.397042-1-mushi.shar@gmail.com Signed-off-by:
-
Krzysztof Kozlowski authored
commit b9c19396 upstream. Correct few frequencies in presence rate table - multiplied by 10 (110250 instead of 11025 Hz). Fixes: abb9c9b8 ("slimbus: stream: add stream support") Cc: <stable@vger.kernel.org> Signed-off-by:
Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org> Link: https://lore.kernel.org/r/20220929165202.410937-1-krzysztof.kozlowski@linaro.org Signed-off-by:
-
Zheng Bin authored
commit e54fad80 upstream. If CONFIG_SLIM_QCOM_NGD_CTRL=y, CONFIG_QCOM_RPROC_COMMON=m, COMPILE_TEST=y, bulding fails: drivers/slimbus/qcom-ngd-ctrl.o: In function `qcom_slim_ngd_ctrl_probe': qcom-ngd-ctrl.c:(.text+0x330): undefined reference to `qcom_register_ssr_notifier' qcom-ngd-ctrl.c:(.text+0x5fc): undefined reference to `qcom_unregister_ssr_notifier' drivers/slimbus/qcom-ngd-ctrl.o: In function `qcom_slim_ngd_remove': qcom-ngd-ctrl.c:(.text+0x90c): undefined reference to `qcom_unregister_ssr_notifier' Make SLIM_QCOM_NGD_CTRL depends on QCOM_RPROC_COMMON || (COMPILE_TEST && !QCOM_RPROC_COMMON) to fix this. Fixes: e291691c ("slimbus: qcom-ngd-ctrl: allow compile testing without QCOM_RPROC_COMMON") Cc: stable <stable@kernel.org> Signed-off-by:
Zheng Bin <zhengbin13@huawei.com> Reviewed-by:
-
Johan Hovold authored
commit 5c294de3 upstream. This reverts commit 6000b8d9. The offending commit disabled the USB core PHY management as the dwc3 already manages the PHYs in question. Unfortunately some platforms have started relying on having USB core also controlling the PHY and this is specifically currently needed on some Exynos platforms for PHY calibration or connected device may fail to enumerate. The PHY calibration was previously handled in the dwc3 driver, but to work around some issues related to how the dwc3 driver interacts with xhci (e.g. using multiple drivers) this was moved to USB core by commits 34c7ed72 ("usb: core: phy: add support for PHY calibration") and a0a46556 ("usb: dwc3: remove generic PHY calibrate() calls"). The same PHY obviously should not be controlled from two different places, which for example do no agree on the PHY mode or power state during suspend, but as the offending patch was backported to stable, let's revert it for now. Reported-by:
Stefan Agner <stefan@agner.ch> Link: https://lore.kernel.org/lkml/808bdba846bb60456adf10a3016911ee@agner.ch/ Fixes: 6000b8d9 ("usb: dwc3: disable USB core PHY management") Cc: stable@vger.kernel.org Signed-off-by:
Johan Hovold <johan+linaro@kernel.org> Tested-by:
Marek Szyprowski <m.szyprowski@samsung.com> Acked-by:
Thinh Nguyen <Thinh.Nguyen@synopsys.com> Link: https://lore.kernel.org/r/20221103144648.14197-1-johan+linaro@kernel.org Signed-off-by:
-
Takashi Iwai authored
commit 1abfd71e upstream. Samsung Galaxy Book Pro 360 (13" 2021 NP930QBD-ke1US) with codec SSID 144d:c1a6 requires the same workaround for enabling the speaker amp like other Samsung models with ALC298 codec. Link: https://bugzilla.opensuse.org/show_bug.cgi?id=1205100 Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20221115170235.18875-1-tiwai@suse.de Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Emil Flink authored
commit b18a4563 upstream. The Samsung Galaxy Book Pro seems to have the same issue as a few other Samsung laptops, detailed in kernel bug report 207423. Sound from headphone jack works, but not the built-in speakers. alsa-info: http://alsa-project.org/db/?f=b40ba609dc6ae28dc84ad404a0d8a4bbcd8bea6d Signed-off-by:
Emil Flink <emil.flink@gmail.com> Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/20221115144500.7782-1-emil.flink@gmail.com Signed-off-by:
-
Takashi Iwai authored
commit ad72c3c3 upstream. snd_usbmidi_output_open() has a check of the NULL port with snd_BUG_ON(). snd_BUG_ON() was used as this shouldn't have happened, but in reality, the NULL port may be seen when the device gives an invalid endpoint setup at the descriptor, hence the driver skips the allocation. That is, the check itself is valid and snd_BUG_ON() should be dropped from there. Otherwise it's confusing as if it were a real bug, as recently syzbot stumbled on it. Reported-by: syzbot+9abda841d636d86c41da@syzkaller.appspotmail.com Cc: <stable@vger.kernel.org> Link: https://lore.kernel.org/r/syzbot+9abda841d636d86c41da@syzkaller.appspotmail.com Link: https://lore.kernel.org/r/20221112141223.6144-1-tiwai@suse.de Signed-off-by:
-
Rodrigo Siqueira authored
commit 7af87fc1 upstream. On IGT, there is a test named amd_hotplug, and when the subtest basic is executed on DCN31, we get the following error: [drm] *ERROR* [CRTC:71:crtc-0] flip_done timed out [drm] *ERROR* flip_done timed out [drm] *ERROR* [CRTC:71:crtc-0] commit wait timed out [drm] *ERROR* flip_done timed out [drm] *ERROR* [CONNECTOR:88:DP-1] commit wait timed out [drm] *ERROR* flip_done timed out [drm] *ERROR* [PLANE:59:plane-3] commit wait timed out After enable the page flip log with the below command: echo -n 'format "[PFLIP]" +p' > /sys/kernel/debug/dynamic_debug/control It is possible to see that the flip was submitted, but DC never replied back, which generates time-out issues. This is an indication that the HUBP surface flip is missing. This commit fixes this issue by adding hubp1_set_flip_int to DCN31. Reviewed-by:
Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com> Acked-by:
Tom Chung <chiahsuan.chung@amd.com> Signed-off-by:
Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Tested-by:
Daniel Wheeler <daniel.wheeler@amd.com> Signed-off-by:
Alex Deucher <alexander.deucher@amd.com> Cc: stable@vger.kernel.org Signed-off-by:
-
Shang XiaoJing authored
commit 22ea4ca9 upstream. When test_gen_kprobe_cmd() failed after kprobe_event_gen_cmd_end(), it will goto delete, which will call kprobe_event_delete() and release the corresponding resource. However, the trace_array in gen_kretprobe_test will point to the invalid resource. Set gen_kretprobe_test to NULL after called kprobe_event_delete() to prevent null-ptr-deref. BUG: kernel NULL pointer dereference, address: 0000000000000070 PGD 0 P4D 0 Oops: 0000 [#1] SMP PTI CPU: 0 PID: 246 Comm: modprobe Tainted: G W 6.1.0-rc1-00174-g9522dc5c87da-dirty #248 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.15.0-0-g2dd4b9b3f840-prebuilt.qemu.org 04/01/2014 RIP: 0010:__ftrace_set_clr_event_nolock+0x53/0x1b0 Code: e8 82 26 fc ff 49 8b 1e c7 44 24 0c ea ff ff ff 49 39 de 0f 84 3c 01 00 00 c7 44 24 18 00 00 00 00 e8 61 26 fc ff 48 8b 6b 10 <44> 8b 65 70 4c 8b 6d 18 41 f7 c4 00 02 00 00 75 2f RSP: 0018:ffffc9000159fe00 EFLAGS: 00010293 RAX: 0000000000000000 RBX: ffff88810971d268 RCX: 0000000000000000 RDX: ffff8881080be600 RSI: ffffffff811b48ff RDI: ffff88810971d058 RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000001 R10: ffffc9000159fe58 R11: 0000000000000001 R12: ffffffffa0001064 R13: ffffffffa000106c R14: ffff88810971d238 R15: 0000000000000000 FS: 00007f89eeff6540(0000) GS:ffff88813b600000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 0000000000000070 CR3: 000000010599e004 CR4: 0000000000330ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> __ftrace_set_clr_event+0x3e/0x60 trace_array_set_clr_event+0x35/0x50 ? 0xffffffffa0000000 kprobe_event_gen_test_exit+0xcd/0x10b [kprobe_event_gen_test] __x64_sys_delete_module+0x206/0x380 ? lockdep_hardirqs_on_prepare+0xd8/0x190 ? syscall_enter_from_user_mode+0x1c/0x50 do_syscall_64+0x3f/0x90 entry_SYSCALL_64_after_hwframe+0x63/0xcd RIP: 0033:0x7f89eeb061b7 Link: https://lore.kernel.org/all/20221108015130.28326-3-shangxiaojing@huawei.com/ Fixes: 64836248 ("tracing: Add kprobe event command generation test module") Signed-off-by:
Shang XiaoJing <shangxiaojing@huawei.com> Cc: stable@vger.kernel.org Acked-by:
Masami Hiramatsu (Google) <mhiramat@kernel.org> Signed-off-by:
-
Shang XiaoJing authored
commit e0d75267 upstream. When trace_get_event_file() failed, gen_kretprobe_test will be assigned as the error code. If module kprobe_event_gen_test is removed now, the null pointer dereference will happen in kprobe_event_gen_test_exit(). Check if gen_kprobe_test or gen_kretprobe_test is error code or NULL before dereference them. BUG: kernel NULL pointer dereference, address: 0000000000000012 PGD 0 P4D 0 Oops: 0000 [#1] SMP PTI CPU: 3 PID: 2210 Comm: modprobe Not tainted 6.1.0-rc1-00171-g2159299a3b74-dirty #217 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.15.0-0-g2dd4b9b3f840-prebuilt.qemu.org 04/01/2014 RIP: 0010:kprobe_event_gen_test_exit+0x1c/0xb5 [kprobe_event_gen_test] Code: Unable to access opcode bytes at 0xffffffff9ffffff2. RSP: 0018:ffffc900015bfeb8 EFLAGS: 00010246 RAX: ffffffffffffffea RBX: ffffffffa0002080 RCX: 0000000000000000 RDX: ffffffffa0001054 RSI: ffffffffa0001064 RDI: ffffffffdfc6349c RBP: ffffffffa0000000 R08: 0000000000000004 R09: 00000000001e95c0 R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000000800 R13: ffffffffa0002420 R14: 0000000000000000 R15: 0000000000000000 FS: 00007f56b75be540(0000) GS:ffff88813bc00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: ffffffff9ffffff2 CR3: 000000010874a006 CR4: 0000000000330ee0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> __x64_sys_delete_module+0x206/0x380 ? lockdep_hardirqs_on_prepare+0xd8/0x190 ? syscall_enter_from_user_mode+0x1c/0x50 do_syscall_64+0x3f/0x90 entry_SYSCALL_64_after_hwframe+0x63/0xcd Link: https://lore.kernel.org/all/20221108015130.28326-2-shangxiaojing@huawei.com/ Fixes: 64836248 ("tracing: Add kprobe event command generation test module") Signed-off-by:
-
Steven Rostedt (Google) authored
commit 94eedf3d upstream. The flag that tells the event to call its triggers after reading the event is set for eprobes after the eprobe is enabled. This leads to a race where the eprobe may be triggered at the beginning of the event where the record information is NULL. The eprobe then dereferences the NULL record causing a NULL kernel pointer bug. Test for a NULL record to keep this from happening. Link: https://lore.kernel.org/linux-trace-kernel/20221116192552.1066630-1-rafaelmendsr@gmail.com/ Link: https://lore.kernel.org/linux-trace-kernel/20221117214249.2addbe10@gandalf.local.home Cc: Linux Trace Kernel <linux-trace-kernel@vger.kernel.org> Cc: Tzvetomir Stoyanov <tz.stoyanov@gmail.com> Cc: Tom Zanussi <zanussi@kernel.org> Cc: stable@vger.kernel.org Fixes: 7491e2c4 ("tracing: Add a probe that attaches to trace events") Acked-by:
Rafael Mendonca <rafaelmendsr@gmail.com> Signed-off-by:
Steven Rostedt (Google) <rostedt@goodmis.org> Signed-off-by:
-
Shang XiaoJing authored
commit 1b5f1c34 upstream. In register_synth_event(), if set_synth_event_print_fmt() failed, then both trace_remove_event_call() and unregister_trace_event() will be called, which means the trace_event_call will call __unregister_trace_event() twice. As the result, the second unregister will causes the wild-memory-access. register_synth_event set_synth_event_print_fmt failed trace_remove_event_call event_remove if call->event.funcs then __unregister_trace_event (first call) unregister_trace_event __unregister_trace_event (second call) Fix the bug by avoiding to call the second __unregister_trace_event() by checking if the first one is called. general protection fault, probably for non-canonical address 0xfbd59c0000000024: 0000 [#1] SMP KASAN PTI KASAN: maybe wild-memory-access in range [0xdead000000000120-0xdead000000000127] CPU: 0 PID: 3807 Comm: modprobe Not tainted 6.1.0-rc1-00186-g76f33a7eedb4 #299 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.15.0-0-g2dd4b9b3f840-prebuilt.qemu.org 04/01/2014 RIP: 0010:unregister_trace_event+0x6e/0x280 Code: 00 fc ff df 4c 89 ea 48 c1 ea 03 80 3c 02 00 0f 85 0e 02 00 00 48 b8 00 00 00 00 00 fc ff df 4c 8b 63 08 4c 89 e2 48 c1 ea 03 <80> 3c 02 00 0f 85 e2 01 00 00 49 89 2c 24 48 85 ed 74 28 e8 7a 9b RSP: 0018:ffff88810413f370 EFLAGS: 00010a06 RAX: dffffc0000000000 RBX: ffff888105d050b0 RCX: 0000000000000000 RDX: 1bd5a00000000024 RSI: ffff888119e276e0 RDI: ffffffff835a8b20 RBP: dead000000000100 R08: 0000000000000000 R09: fffffbfff0913481 R10: ffffffff8489a407 R11: fffffbfff0913480 R12: dead000000000122 R13: ffff888105d050b8 R14: 0000000000000000 R15: ffff888105d05028 FS: 00007f7823e8d540(0000) GS:ffff888119e00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f7823e7ebec CR3: 000000010a058002 CR4: 0000000000330ef0 DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400 Call Trace: <TASK> __create_synth_event+0x1e37/0x1eb0 create_or_delete_synth_event+0x110/0x250 synth_event_run_command+0x2f/0x110 test_gen_synth_cmd+0x170/0x2eb [synth_event_gen_test] synth_event_gen_test_init+0x76/0x9bc [synth_event_gen_test] do_one_initcall+0xdb/0x480 do_init_module+0x1cf/0x680 load_module+0x6a50/0x70a0 __do_sys_finit_module+0x12f/0x1c0 do_syscall_64+0x3f/0x90 entry_SYSCALL_64_after_hwframe+0x63/0xcd Link: https://lkml.kernel.org/r/20221117012346.22647-3-shangxiaojing@huawei.com Fixes: 4b147936 ("tracing: Add support for 'synthetic' events") Signed-off-by:
-
Shang XiaoJing authored
commit a4527fef upstream. test_gen_synth_cmd() only free buf in fail path, hence buf will leak when there is no failure. Add kfree(buf) to prevent the memleak. The same reason and solution in test_empty_synth_event(). unreferenced object 0xffff8881127de000 (size 2048): comm "modprobe", pid 247, jiffies 4294972316 (age 78.756s) hex dump (first 32 bytes): 20 67 65 6e 5f 73 79 6e 74 68 5f 74 65 73 74 20 gen_synth_test 20 70 69 64 5f 74 20 6e 65 78 74 5f 70 69 64 5f pid_t next_pid_ backtrace: [<000000004254801a>] kmalloc_trace+0x26/0x100 [<0000000039eb1cf5>] 0xffffffffa00083cd [<000000000e8c3bc8>] 0xffffffffa00086ba [<00000000c293d1ea>] do_one_initcall+0xdb/0x480 [<00000000aa189e6d>] do_init_module+0x1cf/0x680 [<00000000d513222b>] load_module+0x6a50/0x70a0 [<000000001fd4d529>] __do_sys_finit_module+0x12f/0x1c0 [<00000000b36c4c0f>] do_syscall_64+0x3f/0x90 [<00000000bbf20cf3>] entry_SYSCALL_64_after_hwframe+0x63/0xcd unreferenced object 0xffff8881127df000 (size 2048): comm "modprobe", pid 247, jiffies 4294972324 (age 78.728s) hex dump (first 32 bytes): 20 65 6d 70 74 79 5f 73 79 6e 74 68 5f 74 65 73 empty_synth_tes 74 20 20 70 69 64 5f 74 20 6e 65 78 74 5f 70 69 t pid_t next_pi backtrace: [<000000004254801a>] kmalloc_trace+0x26/0x100 [<00000000d4db9a3d>] 0xffffffffa0008071 [<00000000c31354a5>] 0xffffffffa00086ce [<00000000c293d1ea>] do_one_initcall+0xdb/0x480 [<00000000aa189e6d>] do_init_module+0x1cf/0x680 [<00000000d513222b>] load_module+0x6a50/0x70a0 [<000000001fd4d529>] __do_sys_finit_module+0x12f/0x1c0 [<00000000b36c4c0f>] do_syscall_64+0x3f/0x90 [<00000000bbf20cf3>] entry_SYSCALL_64_after_hwframe+0x63/0xcd Link: https://lkml.kernel.org/r/20221117012346.22647-2-shangxiaojing@huawei.com Cc: <mhiramat@kernel.org> Cc: <zanussi@kernel.org> Cc: <fengguang.wu@intel.com> Cc: stable@vger.kernel.org Fixes: 9fe41efa ("tracing: Add synth event generation test module") Signed-off-by:
-
